Mitsubishi PAJERO IV Service Manual Download Page 72

Page: 72 / 72

OTHERS

PERIODIC INSPECTION AND MAINTENANCE

2-48

OTHERS

F1. CHECK BODY CONDITION FOR
DAMAGE

M6020700100254

1. Check underbody coating for damage.
2. Check body painting for damage.

F2. CHECK THE COMMON RAIL ENGINE
(small injection quantity learning)

M6020700400017

LEARNING PROCEDURE

1. After the ignition switch is in "LOCK" (OFF)

position, connect the M.U.T.-III to the diagnosis
connector.

2. Put the vehicle in the following idling stable

conditions:

•

Engine coolant temperature: 80

−

•

Automatic transmission fluid temperature: 60

or higher

•

Lamps, A/C condenser fan and all accessories:
OFF

•

Transmission: Neutral <M/T>, "P" range <A/T>

•

Power steering: Static state

3. Select SPECIAL FUNCTION from the function

menu.

4. Select SMALL INJECTION QUANTITY

LEARNING from the SPECIAL FUNCTION menu
to execute learning.

CAUTION

•

If the vehicle conditions go out of the learning
conditions during idling, learning is inter-
rupted.

•

To reexecute learning, the ignition switch
must once be turned off.

5. Continue idling for about 3 minutes before

learning is completed.

6. Confirm that the engine warning lamp is off. If it

still blinks, reexecute learning.

F3. ROAD TEST

M6020700200325

Drive the vehicle and check for conditions.
1. Check free play of steering wheel.
2. Check efficiency of service brakes and parking

brakes system.

3. Check driveability of engine.
4. Check condition of instruments, gauges

indicators, exterior lamps, heater and ventilators.

5. Check abnormal noise of each part.
6. Check the tyres for wear and for the correct air

pressure.

AC608423

Diagnosis
connector

MB991827

MB991824

MB991910

AC609417

Summary of Contents for PAJERO IV









































































Search results

Summary of Contents for PAJERO IV

Reviews:

Related manuals for PAJERO IV

Brands by name

Popular brands

Mitsubishi PAJERO IV, Service Manual

Search results

Summary of Contents for PAJERO IV

Reviews:

Related manuals for PAJERO IV

Brands by name

Popular brands