Mitsubishi PAJERO IV Service Manual Download Page 64

Page: 64 / 72

OPERATIONS AFTER ENGINE IS WARMED UP

PERIODIC INSPECTION AND MAINTENANCE

2-40

4. Install a new engine oil pan drain plug gasket so

that it faces in the direction shown in the
illustration, and then tighten the engine oil pan
drain plug to the specified torque.

Tightening torque: 39

5 N

⋅

5. Refill with specified quantity of engine oil.

Specified Engine Oil

•

ACEA classification: "For service
A1/B1, A3/B3, A3/B4 or A5/B5"

•

API classification: "For service CD" or
higher

Total quantity (Includes volume inside oil filter

and oil cooler): 9.8 L

6. Install the engine oil filler cap.
7. Check engine oil level.

E4. REPLACE ENGINE OIL FILTER

M6020600400526

<6G7>

1. Start the engine and allow it to warm up until the

temperature of the coolant reaches 80

C to 90

CAUTION

Use care as engine oil could be hot.

2. Remove the oil filler cap.
3. Remove the engine oil pan drain plug to drain

engine oil.

4. Remove the under cover.

5. Use the special tool oil filter wrench (MB991610)

to remove the oil filter.

6. Clean the filter bracket side mounting surface.

7. Apply a small amount of engine oil to the O-ring of

the new oil filter.

Oil filter number: MD352626

8. Once the O-ring of the oil filter is touching the

flange, use the special tool oil filter wrench
(MB991610) to tighten to the specified torque.

Tightening torque: Approximately 3/4 turn
(14

2 N

⋅

9. Install the engine oil pan drain plug and refill the

engine oil.

10.Race the engine 2

−

3 times, and check to be sure

that no engine oil leaks from installation section of
the oil filter.

11.Install the under cover.

<4M4>

1. Start the engine and allow it to warm up until the

temperature of the coolant reaches 80

C to 90

CAUTION

Use care as engine oil could be hot.

2. Remove the oil filler cap.
3. Remove the engine oil pan drain plug to drain

engine oil.

4. Remove the under cover.

AC609879AB

Engine oil pan side

Engine oil pan
drain plug gasket

AC609880

AC609881AB

MB991610

AC609882AB

O-ring

Summary of Contents for PAJERO IV









































































Search results

Summary of Contents for PAJERO IV

Reviews:

Related manuals for PAJERO IV

Brands by name

Popular brands

Mitsubishi PAJERO IV, Service Manual

Search results

Summary of Contents for PAJERO IV

Reviews:

Related manuals for PAJERO IV

Brands by name

Popular brands