Mitsubishi PAJERO IV Service Manual Download Page 23

Page: 23 / 72

FINAL STEPS

PRE-DELIVERY INSPECTION

1-17

NOTE: For the specified oil, refer to GROUP 2,
Periodic Inspection and Maintenance.

41. HOSES, FLUID LINES AND
CONNECTIONS LOCATED UNDER
VEHICLE

M6010901000145

1. Check all hoses, fluid lines and connections for

leaks.

2. Check all hoses and fluid lines for proper routing

away from sharp edges and moving components.

FINAL STEPS

42. HEADLAMP AIMING

M6011000100116

Check condition for headlamp aiming.

NOTE: For headlamp aiming procedures, refer to the
Workshop Manual for that model.

43. EQUIPMENT

M6011000200050

Check the installation of the various equipment.
1. Floor mats
2. Spare tyre
3. Jack, jack handle and tool set

44. EXTERIOR AND INTERIOR

M6011000300187

Finally check and clean the exterior and interior.
1. Wash the vehicle to remove all traces of road

grime and other dirt on the vehicle as a result of
new vehicle preparations.

2. Clean exterior and interior glass surface.
3. Remove all protective covers.
4. Remove undercoat overspray, excess window

sealer, and excess weatherstrip adhesive.

5. Verify that the secondary key can not unlock the

glove box and tailgate/boot lid (if so equipped).

6. Remove shipping and inspection stickers.

45. OWNER INSTRUCTIONS

M6011000400054

1. Verify that the owner's manual and service

booklet is in the glove box.

2. Place the spare keys in envelope in the glove box

before delivery.

AC305647

AC305648

Level surface

Headlamp

Screen

AC305649

Summary of Contents for PAJERO IV









































































Search results

Summary of Contents for PAJERO IV

Reviews:

Related manuals for PAJERO IV

Brands by name

Popular brands

Mitsubishi PAJERO IV, Service Manual

Search results

Summary of Contents for PAJERO IV

Reviews:

Related manuals for PAJERO IV

Brands by name

Popular brands