Mitsubishi PAJERO IV Service Manual Download Page 22

Page: 22 / 72

AFTER ROAD TEST

PRE-DELIVERY INSPECTION

1-16

36. HOSES, FLUID LINES AND
CONNECTIONS LOCATED UNDER HOOD

M6010900400203

CAUTION

Remember that the air conditioner system is
under pressure.

1. Check all brake, fuel, power steering and air

conditioner lines and connections; verify proper
routing, check connections for leaks, tighten loose
connector as required.

2. Inspect routing and connections of all vacuum,

and radiator and heater houses.

NOTE: Keep in mind that an oily residue around
an air conditioner connector does not necessarily
indicate a leak. Oil is used to lubricate fittings dur-
ing assembly. Be sure lines are not twisted or
kinked.

37. MANUAL TRANSMISSION AND
TRANSFER (4WD) OIL LEVEL

M6010900500211

1. Remove the filler plug.
2. Check the oil level. If the oil level is at or slightly

below the filler hole, it is in satisfactory condition.

3. If the level is low, replenish the transmission and

transfer case with fresh oil by using a lubricator.

NOTE: For the specified oil, refer to GROUP 2,
Periodic Inspection and Maintenance.

38. AUTOMATIC TRANSMISSION FLUID
LEVEL

M6010900600230

1. Remove the dipstick and check the fluid level.
2. Fluid level is okay if it is in the specified range as

illustration at normal engine operating
temperature.

3. If the level is below the lower notch, replenish fluid

until the level reaches the upper notch.

NOTE: For the specified automatic transmission
fluid, refer to GROUP 2, Periodic Inspection and
Maintenance.

39. ENGINE, TRANSMISSION, STEERING
GEAR BOX AND DIFFERENTIAL FOR
LEAKS

M6010900700055

Check the engine, transmission, steering gear box
and differential for oil leaks.

40. FRONT AND REAR DIFFERENTIAL
OIL LEVELS

M6010900800234

1. Remove the filler plug.
2. Check the oil level. If the oil level is at or slightly

below the filler hole, it is in satisfactory condition.

•

Type 1 only: Remove the filler plug, and check the

gear oil level. Check that gear oil level is not 8
mm below the bottom of filler plug hole.

3. If the level is low, replenish the front and/or rear

differential with fresh oil by using a lubricator.

AC305643

AC305644

Transmission oil

AC005861AD

AC305646

8 mm

Upper
limit

Lower
limit

Gear oil

TYPE 1

TYPE 2

Summary of Contents for PAJERO IV









































































Search results

Summary of Contents for PAJERO IV

Reviews:

Related manuals for PAJERO IV

Brands by name

Popular brands

Mitsubishi PAJERO IV, Service Manual

Search results

Summary of Contents for PAJERO IV

Reviews:

Related manuals for PAJERO IV

Brands by name

Popular brands