Mitsubishi PAJERO IV Service Manual Download Page 31 | Manualshive

Page: 31 / 72

background image

OPERATIONS INSIDE THE ENGINE COMPARTMENT

PERIODIC INSPECTION AND MAINTENANCE

2-7

OPERATIONS INSIDE THE ENGINE COMPARTMENT

A1. CHECK V-BELT FOR CRACKS,
FRAYING, WEAR, AND ADJUST ITS
TENSION

M6020200100561

V-BELT CONDITION

Check the whole rounds of the V-belt for cracks, fray-
ing and wear.

V-BELT TENSION
ALTERNATOR DRIVE BELT TENSION
CHECK <6G7>

CAUTION

Check the alternator drive belt tension after turn-
ing the crankshaft clockwise one turn or more.

1. Make sure that the indicator mark is within the

area marked with A in the illustration.

2. If the mark is out of the area, replace the drive

belt.

NOTE: The alternator drive belt tension check is
not necessary as alternator drive belt auto-ten-
sioner is adopted.

ALTERNATOR DRIVE BELT TENSION
CHECK AND ADJUSTMENT <4M4>

Check the drive belt tension in the following proce-
dure.

STANDARD VALUE:

<4M40>

<4M41>

<WHEN THE VIBRATION FREQUENCY IS
MEASURED {SPECIAL TOOL (MB992080)
IS USED}: RECOMMENDATION>

NOTE: The vibration frequency measuring method is
recommended for check and adjustment of the drive
belt tension.

1. Connect the Special tool microphone assembly

(MB992082) to the Special tool belt tension meter
(MB992081) of the Special tool belt tension meter
set (MB992080).

2. Press the "POWER" button to turn on the power

supply.

3. Press number key 1. Check to ensure that "No.

01" appears on the upper left of the display and
that the following numeric values are displayed for
individual items (M, W, and S):
M 000.9 g/m
W 010.0 mm/R
S 0100 mm
If numeric values have not been entered (new
tool), set them according to the belt specifications
as shown below. Once you set them, you do not
have to set them again. The settings remain
undeleted even after battery replacement.

Item

When
checked

When
adjusted

When
replaced

Vibration
frequency
Hz

103

−

132

111

−

125

132

−

156

Tension N

294

−

490

343

−

441

490

−

686

Deflection
mm
(Reference)

8.0

−

11.0

9.0

−

11.0

8.0

−

9.0

AC511210AB

Alternator drive belt
auto-tensioner

A

Indicator mark

Item

When
checked

When
adjusted

When
replaced

Vibration
frequency
Hz

150

−

201

164

−

190

190

−

232

Tension N

245

−

441

294

−

392

392

−

588

Deflection
mm
(Reference)

9.1

−

12.7

9.8

−

11.7

7.2

−

9.8

AC507219AB

MB992082

MB992081

Belt tension meter set (MB992080)

«
...
29
30
31
32
33
...
»

Summary of Contents for PAJERO IV









































































Reviews:

No comments

Related manuals for PAJERO IV

Brand: A-Tach Mounts Pages: 2

Brand: Abarth Pages: 176

Brand: Jabra Pages: 2

Brand: Jabra Pages: 38

Sprinter Bed System Adventure Wagon Kit

Brand: FVC Pages: 8

Brand: Axxess Pages: 8

Brand: EUFAB Pages: 12

Brand: Jaeger Pages: 13

Brand: Conrad Pages: 50

Brand: Kuda Pages: 3

Brand: Westin Pages: 3

Brand: DRAGONFIRE Pages: 4

Bounder turbo diesel 2001

Brand: Fleetwood Pages: 166

Brand: Scion Pages: 58

Brand: Kia Pages: 46

Brand: NavLinkz Pages: 26

Brand: NavLinkz Pages: 24

Brand: Toyota Pages: 277

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands