Mitsubishi PAJERO IV Service Manual Download Page 33 | Manualshive

Page: 33 / 72

background image

OPERATIONS INSIDE THE ENGINE COMPARTMENT

PERIODIC INSPECTION AND MAINTENANCE

2-9

<WHEN USING THE TENSION GAUGE>

Use a belt tension gauge to check that the belt ten-
sion is within the standard value.

<BELT DEFLECTION CHECK>

Apply approximately 100 N of force to the middle of
the drive belt between the pulleys (at the place indi-
cated by the arrow) and check that the amount of
deflection is within the standard value.
When the belt tension is adjusted by measuring the
deflection, adjust it with a tool for vibration frequency
measurement or tension measurement afterward.

If not within the standard value, adjust the belt ten-
sion by the following procedure.

1. Loosen the nut of the alternator pivot bolt.
2. Loosen the alternator fixing nut.
3. Use the adjusting bolt to adjust the belt tension

and belt deflection to the standard values.

4. Tighten the nut for alternator pivot bolt.

Tightening torque: 47

±

9 N

⋅

m

5. Tighten the alternator fixing nut.

Tightening torque: 24

±

4 N

⋅

m

6. Tighten the adjusting bolt.

Tightening torque: 5.0

±

1.0 N

⋅

m

A2. CHECK VACUUM PUMP OIL HOSE
FOR DAMAGE

M6020200400108

1. Inspect the surface of hose for evidence of heat

and mechanical damage.

A3. CHECK INTAKE AIR HOSE AND
TURBOCHARGER OIL HOSE FOR
DAMAGE

M6020200500235

1. Inspect the intake air hoses for cracks or dam-

age.

2. Inspect the turbocharger oil hoses for cracks or

damage.

A4. REPLACE ENGINE TIMING BELT
<EXCEPT VEHICLES WITH TIMING
CHAIN>

M6020200600306

For information concerning the replacement proce-
dures, refer to the Workshop Manual.

AC600285AB

Alternator
pulley

Tension
gauge

Water pump
pulley

AK500540AB

Alternator pulley

Deflection

Crankshaft
pulley

Water pump
pulley

Approximately
100N

AC702321AB

Alternator
fixing nut

Alternator pivot bolt

Adjusting
bolt

AC502483AE

Hose

AC305652

Turbocharger

AB

«
...
31
32
33
34
35
...
»

Summary of Contents for PAJERO IV









































































Reviews:

No comments

Related manuals for PAJERO IV

Brand: ABL Pages: 176

Brand: ABL Pages: 94

Brand: Metra Electronics Pages: 12

Brand: Halfords Pages: 4

Brand: Axxess Pages: 8

Brand: SeaSucker Pages: 9

Brand: Edelbrock Pages: 2

Brand: Compass Pages: 16

Brand: Curt Manufacturing Pages: 6

Tata Indigo Diesel

Brand: TATA Motors Pages: 190

Prime Design HBR-E-FT33B

Brand: Safe Fleet Pages: 12

1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P

Brand: Havis-Shields Pages: 1

Brand: Subaru Pages: 19

Brand: TATA Motors Pages: 166

Brand: Advanced Diagnostics Pages: 10

Brand: Mont Blanc Pages: 2

Brand: Metra Electronics Pages: 20

3 Facelift 2006

Brand: Mazda Pages: 94

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands