Mitsubishi PAJERO IV Service Manual Download Page 46

Page: 46 / 72

OPERATIONS INSIDE THE ENGINE COMPARTMENT

PERIODIC INSPECTION AND MAINTENANCE

2-22

4. Disconnect the fuel tank pump module assembly

connector, fuel tank suction hose, fuel
high-pressure tube.

5. Remove the mounting nuts and retainer plate, and

remove the fuel pump module assembly from the
service hole.

6. Replace the fuel tank filter assembly and packing

with a new one.

7. Install the fuel tank pump module assembly to the

fuel tank through the service hole.

8. Install the retainer plate to the fuel tank and

tighten the mounting nuts.

9. Connect the fuel tank pump module assembly

connector, fuel tank suction hose, fuel
high-pressure tube.

CAUTION

After connecting the fuel high-pressure tube,
slightly pull it to ensure that it is installed
securely. Also confirm that there is a play
approximately 3 mm.

10.Install the service hole cover (lower side).
11.Install the service hole cover (upper side).
12.Restore the second seat (R.H.).

<4M4>

1. Remove the fuel tank cap to release the pressure

inside the fuel tank.

2. Disconnect the connector and the fuel hose, and

then remove the fuel filter assembly from the
bracket.

3. Remove the water level sensor.

4. Use an oil filter wrench to remove the fuel filter

cartridge from the fuel filter pump body.

AC703272

Fuel tank suction
hose

Fuel high-pressure
tube

Fuel tank pump module
assembly connector

AC703246

FUEL PUMP
MODULE

Fuel tank filter
assembly

Fuel tank
pump
assembly

Packing

AC703276

3 mm

Fuel high-pressure tube

Fuel tank pump
module assembly

Quick connector

AC610457AB

Fuel filter assembly

<4M40>

AC608826AB

Fuel filter
assembly

<4M41>

AC609422

Summary of Contents for PAJERO IV









































































Search results

Summary of Contents for PAJERO IV

Reviews:

Related manuals for PAJERO IV

Brands by name

Popular brands

Mitsubishi PAJERO IV, Service Manual

Search results

Summary of Contents for PAJERO IV

Reviews:

Related manuals for PAJERO IV

Brands by name

Popular brands