Mitsubishi PAJERO IV Service Manual Download Page 50

Page: 50 / 72

OPERATIONS UNDER THE VEHICLE

PERIODIC INSPECTION AND MAINTENANCE

2-26

2. Check to be sure that the seal and boot of the ball

joint are correctly installed (in the correct
position), and that they are not damaged.

3. Check tie-rod end lock nut for looseness. If lock

nut is loose, adjust toe-in and then tighten lock nut
to the specified torque.

Tightening torque: 93

15 N

⋅

B6. CHECK GEAR OIL LEVEL IN MANUAL
TRANSMISSION

M6020300600206

1. Remove the filler plug.
2. Check that oil level is up to the lower edge of the

filler plug hole.

3. Check that the oil is not noticeably dirty.
4. Tighten the filler plug to the specified torque.

Tightening torque: 32

2 N

⋅

B7. CHECK GEAR OIL LEVEL IN
TRANSFER CASE (4WD)

M6020300700236

1. Remove the filler plug.
2. Check that oil level is up to the lower edge of the

filler plug hole.

3. Check that the oil is not noticeably dirty.
4. Tighten the filler plug to the specified torque.

Tightening torque: 32

2 N

⋅

B8. CHANGE GEAR OIL IN MANUAL
TRANSMISSION

M6020300800244

1. Remove the oil filler plug.
2. Remove the drain plug and drain the oil.
3. Tighten the filler plug to the specified torque.

Tightening torque: 32

2 N

⋅

4. Fill with specified oil till the level comes to the

lower portion of oil filler plug hole.

Specified transmission oil:

Gear oil API classification GL-4 SAE 75W

−

85W

Quantity: 3.2 L

5. Tighten the filler plug to the specified torque.

Tightening torque: 32

2 N

⋅

AC608838AB

AC604825AB

Filler plug hole

Filler plug

Transmission oil

AC604825AC

Filler plug hole

Filler plug

Transfer oil

AC604827AB

Drain plug

Filler plug

Summary of Contents for PAJERO IV









































































Search results

Summary of Contents for PAJERO IV

Reviews:

Related manuals for PAJERO IV

Brands by name

Popular brands

Mitsubishi PAJERO IV, Service Manual

Search results

Summary of Contents for PAJERO IV

Reviews:

Related manuals for PAJERO IV

Brands by name

Popular brands