Mitsubishi PAJERO IV Service Manual Download Page 37

Page: 37 / 72

OPERATIONS INSIDE THE ENGINE COMPARTMENT

PERIODIC INSPECTION AND MAINTENANCE

2-13

NOTE: Size identification mark: "2775" = 2.775
mm thickness

(3) Remove the camshaft and install the shim

which was selected in step (2).

(4) Re-measure the valve clearances and check

that they are all at the standard value.

5. Turn the crankshaft once to align the notch of the

crankshaft pulley with the timing mark "0".

6. Check and adjust the other valve clearances

according to the step 4.

VALVE CLEARANCE CHECK AND
ADJUSTMENT <4M41>

NOTE: The valve clearance check and adjustment
should be done when the engine is cold.

1. Remove the EGR pipe.

CAUTION

Leaked fuel on parts causes a decrease in func-
tion and burning. Therefore, place waste to
absorb leaked fuel.

2. Use the special tool fuel injection pipe wrench

(MB992188) to remove the fuel injection pipe.

3. Remove the rocker cover.

CAUTION

The crankshaft should always be turned in a
clockwise direction.

4. Align the camshaft sprocket timing marks and set

the No. 1 cylinder at top dead centre.

5. Measure the valve clearance.

If the valve clearance is not as specified, loosen
the rocker arm lock nut and adjust the clearance
using a thickness gauge between the camshaft
and the roller while turning the adjusting screw.

Standard value (cold engine):
Intake valve: 0.10 mm
Exhaust valve: 0.15 mm

AK603848AB

Identification
size mark

AC609910AB

MB992188

AK600672

MB992188

AC610704AB

Timing marks

Crankshaft pulley

Camshaft sprocket

Timing marks

AK500544AB

Exhaust valve side

Intake valve side

Summary of Contents for PAJERO IV









































































Search results

Summary of Contents for PAJERO IV

Reviews:

Related manuals for PAJERO IV

Brands by name

Popular brands

Mitsubishi PAJERO IV, Service Manual

Search results

Summary of Contents for PAJERO IV

Reviews:

Related manuals for PAJERO IV

Brands by name

Popular brands