Mitsubishi MELSEC iQ-R series User Manual Download Page 77

Page: 77 / 86

7 OPERATION EXAMPLES

7.2 Program Examples

Configure the settings in "Application Setting" as follows.

[Navigation window]



[Parameter]



[Module Information]



[R60TCTRT2TT2]



[Module Parameter]



[Application

Setting]

• "Control basic parameters"
Set "Target Value(SV) Setting" of CH1 and "Unused channel setting" of CH2 as shown below.

• "Position-proportional control setting"
Set "Control motor time" and "Addition output limiter setting" as shown below.

• "Alert setting"
Set "Alert 1 mode setting" and "Alert set value 1" of CH1 as shown below.

Use the default values for the parameters other than the parameters shown above.

■

Writing to the CPU module

For the writing to the CPU module, refer to the following.



Page 54 Writing to the CPU module

Auto tuning

For the procedure of auto tuning, refer to the following.



Page 55 Auto tuning

Setting labels

Fort how to set labels, refer to the following.



Page 56 Setting labels

Program examples

For the program examples, refer to the following.



Page 57 Program examples

Summary of Contents for MELSEC iQ-R series























































































Search results

Summary of Contents for MELSEC iQ-R series

Reviews:

Related manuals for MELSEC iQ-R series

Brands by name

Popular brands

Mitsubishi MELSEC iQ-R series, User Manual

Search results

Summary of Contents for MELSEC iQ-R series

Reviews:

Related manuals for MELSEC iQ-R series

Brands by name

Popular brands