Mitsubishi MELSEC iQ-R series User Manual Download Page 57

Page: 57 / 86

7 OPERATION EXAMPLES

7.2 Program Examples

Auto tuning

Perform auto tuning.

[Tool]



[Module Tool List]

Select "Temperature trace" of "Temperature
Control Module" and click the [OK] button.

Select the module to configure the temperature
control setting and click the [OK] button.

Select "Monitor data write" from the following.

[Setting]



[Monitor data write]

Set "Setting/Operation mode command" to
"1:Operation mode command".

Set "Auto tuning command" to "1:ON".

Then, "Auto tuning status" is set to "Executing",
and auto tuning is started.

When auto tuning is completed, "Auto tuning
status" is set to "Stopped".

Temperature control is performed by set PID
constants.

Summary of Contents for MELSEC iQ-R series























































































Search results

Summary of Contents for MELSEC iQ-R series

Reviews:

Related manuals for MELSEC iQ-R series

Brands by name

Popular brands

Mitsubishi MELSEC iQ-R series, User Manual

Search results

Summary of Contents for MELSEC iQ-R series

Reviews:

Related manuals for MELSEC iQ-R series

Brands by name

Popular brands