Mitsubishi MELSEC iQ-R series User Manual Download Page 12 | Manualshive

Page: 12 / 86

background image

10

INTRODUCTION

Thank you for purchasing the Mitsubishi MELSEC iQ-R series programmable controllers.
This manual describes the performance specifications, procedures before operation, wiring, and operation examples of the
relevant products listed below.
Before using this product, please read this manual and the relevant manuals carefully and develop familiarity with the
functions and performance of the MELSEC iQ-R series programmable controller to handle the product correctly.
When applying the program and circuit examples provided in this manual to an actual system, ensure the applicability and
confirm that it will not cause system control problems.
Please make sure that the end users read this manual.

Unless otherwise specified, this manual provides program examples in which the I/O numbers of X/Y0 to X/YF
are assigned to the temperature control module. Assign I/O numbers when applying the program examples to
an actual system. For I/O number assignment, refer to the following.



MELSEC iQ-R Module Configuration Manual

Relevant products

R60TCTRT2TT2, R60TCTRT2TT2BW, R60TCRT4, R60TCRT4BW

COMPLIANCE WITH EMC AND LOW VOLTAGE

DIRECTIVES

Method of ensuring compliance

To ensure that Mitsubishi programmable controllers maintain EMC and Low Voltage Directives when incorporated into other
machinery or equipment, certain measures may be necessary. Please refer to one of the following manuals.
•



MELSEC iQ-R Module Configuration Manual

•



Safety Guidelines (This manual is included with the base unit.)

The CE mark on the side of the programmable controller indicates compliance with EMC and Low Voltage Directives.

Additional measures

To ensure that this product maintains EMC and Low Voltage Directives, please refer to one of the following manuals.
•



MELSEC iQ-R Module Configuration Manual

•



Safety Guidelines (This manual is included with the base unit.)

«
...
10
11
12
13
14
...
»

Summary of Contents for MELSEC iQ-R series























































































Reviews:

No comments

Related manuals for MELSEC iQ-R series

Brand: Eaton Pages: 166

Brand: Samson Pages: 36

Brand: FBII Pages: 71

Brand: CAME Pages: 4

Brand: Eaton Pages: 100

Brand: YUGE Pages: 69

Brand: Quectel Pages: 232

Brand: Quectel Pages: 9

Brand: Quectel Pages: 73

Brand: ValvTechnologies Pages: 20

Brand: Ban Seok Pages: 9

Brand: IBA Pages: 29

Brand: Voltech Pages: 8

PetroVend PV200

Brand: OPW Pages: 2

Brand: Zaiput Flow Technologies Pages: 10

Brand: K&K Pages: 10

Brand: SeaLevel Pages: 115

eTracer ET4415BND

Brand: Epsolar Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands