Mitsubishi MELSEC iQ-R series User Manual Download Page 71

Page: 71 / 86

7 OPERATION EXAMPLES

7.2 Program Examples

Setting labels

GX Works3 has functions supporting program creation.
The following table lists the module labels and global labels used in these program examples.
Do not change the settings of the module labels. For details on global labels, refer to the following.



MELSEC iQ-R Programming Manual (Program Design)

Program examples

■

Program example of the inter-module peak current suppression

■

Program that is processed when the upper limit input alert occurs

For the program that is processed when the upper limit input alert occurs, refer to the following.



Page 57 Program that processes data when the upper limit input alert occurs

Classification

Label name

Description

Device

Module label

R60TC_1.bModuleREADY

Module READY flag

R60TC_2.bModuleREADY

Module READY flag

X10

Label to be defined

Define global labels as follows.

Summary of Contents for MELSEC iQ-R series























































































Search results

Summary of Contents for MELSEC iQ-R series

Reviews:

Related manuals for MELSEC iQ-R series

Brands by name

Popular brands

Mitsubishi MELSEC iQ-R series, User Manual

Search results

Summary of Contents for MELSEC iQ-R series

Reviews:

Related manuals for MELSEC iQ-R series

Brands by name

Popular brands