Mitsubishi MELSEC iQ-R series User Manual Download Page 53

Page: 53 / 86

7 OPERATION EXAMPLES

7.1 Programming Procedure

OPERATION EXAMPLES

This chapter describes the programming procedure and basic program of the temperature control module.

7.1

Programming Procedure

Create a program that operates the temperature control module using the following procedure.

Set parameters.

Create a program.

Using function blocks (FBs) can reduce the load at programming and improve the readability of a program.
For details on the function blocks, refer to the following.



MELSEC iQ-R Temperature Control Module Function Block Reference

7.2

Program Examples

Standard control

System configuration

The following shows a system configuration example.

(1) Power supply module (R61P)
(2) CPU module (R120CPU)
(3) Temperature control module (R60TCTRT2TT2)
(4) Input module (RX10)

(1)

(2)

(3)

(4)

Summary of Contents for MELSEC iQ-R series























































































Search results

Summary of Contents for MELSEC iQ-R series

Reviews:

Related manuals for MELSEC iQ-R series

Brands by name

Popular brands

Mitsubishi MELSEC iQ-R series, User Manual

Search results

Summary of Contents for MELSEC iQ-R series

Reviews:

Related manuals for MELSEC iQ-R series

Brands by name

Popular brands