Mitsubishi MELSEC iQ-R series User Manual Download Page 22 | Manualshive

Page: 22 / 86

background image

20

2 SPECIFICATIONS
2.2 Type of Temperature Sensors, Temperature Measuring Range, Resolution, and Effect from Wiring Resistance

2.2

Type of Temperature Sensors, Temperature
Measuring Range, Resolution, and Effect from

Wiring Resistance

This section describes the types of temperature sensors that can be used with the temperature control module, the
temperature measuring range, the resolution, and the effect from wiring resistance of 1



Thermocouple

The following table lists the types of thermocouples that can be used with the R60TCTRT2TT2 and R60TCTRT2TT2BW, the
temperature measuring range, the resolution, and the effect from wiring resistance of 1



.

*1 Means temperature error per



of wiring resistance of the thermocouple. The error varies depending on measured temperature or

ambient temperature. The temperature error can be corrected by the sensor correction function. (



MELSEC iQ-R Temperature

Control Module User's Manual (Application))

*2 Although a temperature lower than 400



or lower than 800



can be measured, the accuracy cannot be guaranteed.

Thermocouple
type





Temperature
measuring
range

Resolution

Effect from
wiring
resistance of 1



(



/



)

Temperature
measuring
range

Resolution

Effect from
wiring
resistance of 1



(



/



R

0 to 1700

1

0.030

0 to 3000

1

0.054

K

0 to 500
0 to 800
0 to 1300

1

0.005

0 to 1000
0 to 2400

1

0.008

-200.0 to 400.0
0.0 to 400.0
0.0 to 500.0
0.0 to 800.0
-200.0 to 1300.0

0.1

0.0 to 1000.0

0.1

J

0 to 500
0 to 800
0 to 1200

1

0.003

0 to 1000
0 to 1600
0 to 2100

1

0.006

0.0 to 400.0
0.0 to 500.0
0.0 to 800.0
-200.0 to 1000.0

0.1

0.0 to 1000.0

0.1

T

-200 to 400
-200 to 200
0 to 200
0 to 400

1

0.004

0 to 700
-300 to 400

1

0.008

-200.0 to 400.0
0.0 to 400.0

0.1

0.0 to 700.0

0.1

S

0 to 1700

1

0.030

0 to 3000

1

0.054

B

0 to 1800

1

0.038

0 to 3000

1

0.068

E

0 to 400
0 to 1000

1

0.003

0 to 1800

1

0.005

0.0 to 700.0
-200.0 to 1000.0

0.1







N

0 to 1300

1

0.006

0 to 2300

1

0.011

0.0 to 1000.0

0.1







U

0 to 400
-200 to 200

1

0.004

0 to 700
-300 to 400

1

0.009

0.0 to 600.0

0.1







L

0 to 400
0 to 900

1

0.003

0 to 800
0 to 1600

1

0.006

0.0 to 400.0
0.0 to 900.0

0.1







PL



0 to 1200

1

0.005

0 to 2300

1

0.010

W5Re/W26Re

0 to 2300

1

0.017

0 to 3000

1

0.021

«
...
20
21
22
23
24
...
»

Summary of Contents for MELSEC iQ-R series























































































Reviews:

No comments

Related manuals for MELSEC iQ-R series

Brand: Wave Italy Pages: 16

Brand: TA Hydronics Pages: 14

Brand: D+H Pages: 14

Brand: Saga Pages: 9

Brand: nekos Pages: 8

Brand: nekos Pages: 8

Brand: Neles Pages: 12

Brand: Vageo Pages: 2

Brand: Vacon Pages: 6

Brand: Vacon Pages: 24

Brand: Vacon Pages: 30

Brand: Vacon Pages: 81

Brand: Vacon Pages: 100

MusicCAST MCX-CA15

Brand: Yamaha Pages: 176

Brand: IR-Tec Pages: 14

Brand: Ros Pages: 10

Brand: Phoenix Contact Pages: 56

Brand: Daikin Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands