Mitsubishi MELSEC iQ-R series User Manual Download Page 56

Page: 56 / 86

7 OPERATION EXAMPLES
7.2 Program Examples

Configure the settings in "Application Setting" as follows.

[Navigation window]



[Parameter]



[Module Information]



[R60TCTRT2TT2]



[Module Parameter]



[Application

Setting]

• "Control basic parameters"
Set "Target Value(SV) Setting" of CH1 and "Unused channel setting" of CH2 to CH4 as shown below.

• "Limiter setting"
Set "Upper Limit Setting Limiter" of CH1 as shown below.

• "Alert setting"
Set "Alert 1 mode setting" and "Alert set value 1" of CH1 as shown below.

• "Auto tuning setting"
Set "Automatic backup setting after auto tuning of PID constants" of CH1 as shown below.

Use the default values for the parameters other than the parameters shown above.

■

Writing to the CPU module

Write the set parameters to the CPU module, reset the CPU module, and turn off and on the power supply.

[Online]



[Write to PLC]

Summary of Contents for MELSEC iQ-R series























































































Search results

Summary of Contents for MELSEC iQ-R series

Reviews:

Related manuals for MELSEC iQ-R series

Brands by name

Popular brands

Mitsubishi MELSEC iQ-R series, User Manual

Search results

Summary of Contents for MELSEC iQ-R series

Reviews:

Related manuals for MELSEC iQ-R series

Brands by name

Popular brands