Mitsubishi Electric MELSEC iQ-RD77GF16 User Manual Download Page 97 | Manualshive

Page: 97 / 116

background image

APPX

Appendix 2 Component List of the RD77GF

95

A

Appendix 2

Component List of the RD77GF

The positioning system using the Simple Motion module is configured of the following devices.

Reference product

Connection cable

Cables for CC-Link IE Field Network are available from Mitsubishi Electric System & Service Co., Ltd. (Catalogs for cable are
also available.)
In addition, the connector processing of cable length is available for your preference. Please consult your local Mitsubishi
representative.

■

Cable types

The following cable types are available depending on the operating environment:
• Standard type: Cables for inside the control panel and indoor connection
• L type: Cables for outdoor connection
Cables and relay adapters of flame retardant or waterproof type are also available. Please contact your local Mitsubishi
representative.

Recommended product

Hub

Use the recommended hubs listed below. Operation is not guaranteed if hubs other than the recommended ones are used.

Use the CC-Link IE Field Network synchronization communication-compatible switching hubs when using the CC-Link IE
Field Network synchronization communication function.
CC-Link IE Field Network synchronization communication-compatible switching hubs are available from Mitsubishi Electric
System & Service Co., Ltd. Please consult your local Mitsubishi representative.

No.

Part name

Type

Remarks

1

Simple Motion module

RD77GF4

RD77GF8

RD77GF16

RD77GF32

2

Servo amplifier





3

Slave device compatible with
CC-Link IE Field





4

CC-Link IE Field Network
cable



Cables are needed for connecting the Simple Motion module with a servo amplifier/slave
device compatible with CC-Link IE Field, or between servo amplifiers/slave devices
compatible with CC-Link IE Field. (



Page 95 Reference product)

5

Ethernet hub



Switching hubs are needed for connecting the Simple Motion module, a servo amplifier, and
other brand drive units in star topology. (

Page 95 Recommended product)

Ethernet cable

Model (Manufacturer)

CC-Link IE Field Network cable

SC-E5EW series (Mitsubishi Electric System & Service Co., Ltd.)

Type

Model (Manufacturer)

Industrial managed switch

NZ2MHG-T8F2 (Mitsubishi Electric Corporation)

Industrial switching hub

NZ2EHG-T8N (Mitsubishi Electric Corporation)

Type

Model (Manufacturer)

Maximum
extension level

Industrial managed switch

NZ2MHG-T8F2 (Mitsubishi Electric Corporation)

4 levels

CC-Link IE Field Network synchronization communication-compatible
switching hub

DT135TX (Mitsubishi Electric System & Service Co., Ltd.)

4 levels

RD77GF

GF: CC-Link IE Field Network model

Number of controlled axes

«
...
95
96
97
98
99
...
»

Summary of Contents for MELSEC iQ-RD77GF16





















































































































Reviews:

No comments

Related manuals for MELSEC iQ-RD77GF16

Brand: Waterway Pages: 16

Brand: ZETRON Pages: 3

Brand: ADEMCO Pages: 2

Brand: B&G Pages: 2

Brand: B&K Pages: 9

VLT AQUA Drive FC 202

Brand: Danfoss Pages: 124

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 8

Brand: Danfoss Pages: 114

ECL Comfort 300

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 16

Brand: Danfoss Pages: 24

Brand: Danfoss Pages: 8

ECL Comfort 296

Brand: Danfoss Pages: 159

VLT AutomationDrive FC 301

Brand: Danfoss Pages: 78

Brand: Danfoss Pages: 20

ECL Comfort 210

Brand: Danfoss Pages: 12

ECL Comfort 110

Brand: Danfoss Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands