manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-RD77GF16, User Manual

Share
Download
Mitsubishi Electric MELSEC iQ-RD77GF16 User Manual Download Page 66

64

6  WIRING
6.2  External Input Connection Connector of the RD77MS

■

Interface between manual pulse generator/incremental synchronous encoder (Voltage-output 

type/open-collector type)

*1 Set "1: Voltage-output/open-collector type" in "[Pr.89] Manual pulse generator/Incremental synchronous encoder input type selection" if 

the manual pulse generator/incremental synchronous encoder of voltage-output/open-collector type is used.
The default value is "1: Voltage-output/open-collector type".

*2 Set the signal input form in "[Pr.24] Manual pulse generator/Incremental synchronous encoder input selection".
*3 The 5 V DC power supply from the Simple Motion module must not be used if a separate power supply is applied to the manual pulse 

generator/incremental synchronous encoder. If a separate power supply is used, use a stabilized power supply of voltage 5 V DC.
Anything else may cause a failure.

*4 Be sure to connect the 0 V (-) of the manual pulse generator/incremental synchronous encoder and the SG of the Simple Motion 

module.

Wiring example for manual pulse generator/incremental synchronous encoder

Wire the manual pulse generator/incremental synchronous encoder of differential output type and voltage output type/open-
collector type as follows.
Switch the input type of RD77MS by "[Pr.89] Manual pulse generator/Incremental synchronous encoder input type selection".
It is recommended to use the external 5 V power supply (5 V DC±5%) for the power supply of the manual pulse generator/
incremental synchronous encoder. When using the external power supply, do not connect with the 5 V terminal of RD77MS.
When using the internal power supply, connect the 5 V terminal of RD77MS and the 5 V (+) of the manual pulse generator/
incremental synchronous encoder.
In either case, connect the 0 V (-) of the manual pulse generator/incremental synchronous encoder and the SG of RD77MS.
Do not use the 5 V terminal of RD77MS except for connecting the manual pulse generator/incremental synchronous encoder. 
It may cause a failure. Also, do not connect the manual pulse generator/incremental synchronous encoder whose current 
consumption exceeds 200 mA.

Input or 
Output

Signal name

Pin No.

Wiring example

When using the external power supply 
(Recommended)

When using the internal power 
supply

Input

*1, *2

Manual pulse 
generator, A-
phase/PULSE

HA
(A)

1B19

Manual pulse 
generator, B-
phase/SIGN

HB
(B)

1B20

Power 
supply

5 V

*3

1A15
1B15

SG

*4

1A14
1B14

Internal circuit

A

Power supply

5 V DC

External power

supply 5 V DC

B

Manual pulse

generator/

Incremental

synchronous

encoder

5 V

SG

5 V

SG

+

-

+

-

Internal circuit

A

Power supply

5 V DC

B

Manual pulse

generator/

Incremental

synchronous

encoder

5 V

SG

+

-

Summary of Contents for MELSEC iQ-RD77GF16





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands