Miranda XVP-3901 DENSITE series Manual To Installation And Operation Download Page 99 | Manualshive

Page: 99 / 143

background image

GUIDE TO INSTALLATION AND OPERATION

XVP-3901 |

93

5.11.2 Input/Output tab

This tab provides resources to configure the input and output selections and processing of metadata for the XVP-3901
card.

VANC Metadata Extractor

The card can extract 2 Dolby metadata streams from the
VANC interval according to the specified SDID (range = 01 to
09). The presence of each stream is reported in the interface.

VANC Metadata Inserter

The card can insert 2 metadata streams in the VANC interval
for each output (3G/HD and SD outputs). Use the four sets of
pulldowns to configure metadata insertion in VANC Stream 1
and VANC Stream 2 for your outputs.

Insertion: Select the source of metadata to insert

•

Off: No metadata is inserted.

•

Path 1: Metadata from Path 1 is inserted

•

Path 2: Metadata from Path 2 is inserted

•

ABUS A1: Metadata from the ABUS A1 card is inserted

•

ABUS A2: Metadata from the ABUS A2 card is inserted

Insertion Line: Select the VANC line in which the metadata
will be inserted. The range depends on the output format:

•

3G/HD: lines 9 to 20

•

SD (525) lines 12 to 19

•

SD (625) lines 8 to 22

SDID: Select the VANC metadata packet SDID to be
inserted. The SDID is used to specify the relationship between the VANC metadata stream and the first channel of its
associated audio program.

SDID

Associated channel pair

01

No association, or only one audio program

02 Channel

pair

1&2

03 Channel

pair

3&4

04 Channel

pair

5&6

05 Channel

pair

7&8

06 Channel

pair

9&10

07 Channel

pair

11&12

08 Channel

pair

13&14

09 Channel

pair

15&16

Note: If the card is configured to insert a special SDID at the output, any Dolby Metadata packets at the input with the
same SDID will be deleted. Any other SDID packets not inserted by the card will be passed through untouched.

Figure 5.81

Dolby Metadata – Input/Output tab

«
...
97
98
99
100
101
...
»

Summary of Contents for XVP-3901 DENSITE series
















































































































































Reviews:

No comments

Related manuals for XVP-3901 DENSITE series

LaCinema Black RECORD

Brand: LaCie Pages: 5

PowerRouter PR50S

Brand: Nedap Pages: 64

Brand: RGBlink Pages: 13

Brand: Kramer Pages: 12

S-1000MM-M2xx05

Brand: Perle Pages: 12

Sunny Island 3324

Brand: SMA Pages: 80

Proxeo Ultra PB-510

Brand: W&H Pages: 52

Brand: Baumer Pages: 32

Brand: Parallax Pages: 3

Brand: Kramer Pages: 2

Brand: SHENZHEN ENCOM ELECTRIC TECHNOLOGIES CO. Pages: 30

Brand: American Audio Pages: 40

Brand: IMO Pages: 16

Brand: JDS Labs Pages: 5

Soundtouch Stereo JC

Brand: Bose Pages: 34

Brand: Video Messenger Pages: 25

Brand: Biamp Pages: 6

Brand: CYP Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands