Miranda XVP-3901 DENSITE series Manual To Installation And Operation Download Page 114 | Manualshive

Page: 114 / 143

background image

GUIDE TO INSTALLATION AND OPERATION

108

| XVP-3901

5.17 Options panel

Five options are available for the XVP-3901:

•

Discrete AES and 32 Channel Internal Audio Processing Option

(XVP-3901-OPT-AUD)

•

Key/fill

option

(XVP-3901-OPT-K)

•

Dynamic Processing Option

(XVP-3901-OPT-DP)

•

Loudness Measurement option

(XVP-3901-LM)

•

ALC

option

(XVP-3901-OPT-ALC-X)

•

XVP-3901 Full Upgrade option

(XVP-3901-OPT-UG-xx2XVP)

To activate each of these options, you must

•

Obtain a licence key from Miranda Technologies Inc.

•

Type the licence key in the box

•

Click on ENABLE OPTION to enable the option’s features.

5.17.1 Audio option

Enables the discrete AES I/Os, the 32-channel internal audio
processing and the Dolby metadata processing.

Note: When the Audio option is not enabled, all discrete
AES I/Os and audio processing features are disabled. If
there is embedded audio and Dolby metadata in the input
signal, they pass through to the output signal. However,
when the Audio option is not enabled (using a software key)
BUT there are companion audio cards installed and
connected to the XVP-3901 with the ABUS cable, the Audio
Processing, Audio Output and Dolby metadata controls will
be available and functional.

Figure 5.99

Audio option

«
...
112
113
114
115
116
...
»

Summary of Contents for XVP-3901 DENSITE series
















































































































































Reviews:

No comments

Related manuals for XVP-3901 DENSITE series

Brand: Panasonic Pages: 155

SiriusXM CQ-RXBT490U

Brand: Panasonic Pages: 6

Brand: Zena Pages: 12

Brand: Saftronics Pages: 62

MIXHITS iSTREAM2

Brand: ESS Pages: 4

Brand: ScienTECH Pages: 12

IMP-C1000-SFP-bt-24 Series

Brand: ANTAIRA Pages: 2

Brand: ICP DAS USA Pages: 43

Brand: GMI Pages: 9

Digital Video Scaler Series DVS 304 AD

Brand: Extron electronics Pages: 96

Multimedia Enclosure ME3

Brand: Emprex Pages: 40

Brand: Delta Pages: 1

EXT-HDSDI-2-DVISSL

Brand: Gefen Pages: 21

Factory-Link-SPE-M

Brand: I-novative Pages: 12

Brand: Senci Pages: 39

1553-FGC 101 1010 Uen A

Brand: Ericsson Pages: 153

Brand: Baumer Pages: 41

Brand: YOKOGAWA Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands