Miranda XVP-3901 DENSITE series Manual To Installation And Operation Download Page 8

Page: 8 / 143

GUIDE TO INSTALLATION AND OPERATION

| XVP-3901

•

Processes and converts Ancillary data such as CC (608/708), time code and Dolby Metadata

•

Optional optical fiber module

•

Serial and GPIO ports for automation or audio metadata

•

16 channels embedded audio processing (32 channels internal)

•

Offers 4 AES inputs and outputs

•

Audio Downmix: 5.1 to Lt/Rt or Lo/Ro

•

Audio dynamic processor (compressor/limiter/expander)

•

Dolby E compatible

•

Audio metadata insertion, extraction and processing

•

Perfect audio/video synchronization plus additional audio fixed delay of up to 2 seconds

•

Compatible with Miranda audio processing cards like UAP and DAP

•

Optional Dolby-E/Digital (AC-3) encoder/decoder modules

•

Optional Linear Acoustic

upMAX™ module

•

Optional Linear Acoustic ALC module

1.3 XVP-3901

Models

The XVP-3901 is available in models with reduced functionality for applications where the full capabilities of the XVP-
3901 are not required. The various models that are available are described below.

•

Note that each of these models can be upgraded to a fully-functional XVP-3901 with the purchase of an
upgrade key. See Section 5.17 for details.

•

The Audio, Key/Fill and Dynamic Processing options described in Section 5.17 are available on all of these
models.

This chart summarizes the functionality of the various models

Models

Feature

XVP-3901 XVP-3901-FS XVP-3901-DC XVP-3901-UC XVP-3901-XC

SD-to-SD with ARC

•

• •

HD-to-HD, 3G-to-3G (same format)

•

3G/HD-to-3G/HD

• •

SD-to-3G/HD (720p/1080i/1080p)

•

3G/HD (720p/1080i/1080p)-to-SD

•

SD/HD to HD/SD

•

Simultaneous 3G/HD and SD outputs

•

Summary of Contents for XVP-3901 DENSITE series
















































































































































Search results

Summary of Contents for XVP-3901 DENSITE series

Reviews:

Related manuals for XVP-3901 DENSITE series

Brands by name

Popular brands

Miranda XVP-3901 DENSITE series, Manual To Installation And Operation

Search results

Summary of Contents for XVP-3901 DENSITE series

Reviews:

Related manuals for XVP-3901 DENSITE series

Brands by name

Popular brands