Miranda XVP-3901 DENSITE series Manual To Installation And Operation Download Page 3

Page: 3 / 143

GUIDE TO INSTALLATION AND OPERATION

XVP-3901

Table of Contents

XVP-3901 3G/HD/SD Up, Down & Cross Converter with Audio Processor .......................... 1

1.1

Introduction ......................................................................................................................................... 1

1.2

Features .............................................................................................................................................. 1

1.3

XVP-3901 Models ............................................................................................................................... 2

1.3.1

XVP-3901 (full model)............................................................................................................ 3

1.3.2

XVP-3901-FS ......................................................................................................................... 4

1.3.3

XVP-3901-DC ........................................................................................................................ 5

1.3.4

XVP-3901-UC ........................................................................................................................ 6

1.3.5

XVP-3901-XC......................................................................................................................... 7

1.4

Front Card-edge Interface................................................................................................................... 8

Installation .................................................................................................................................. 9

2.1

Unpacking ........................................................................................................................................... 9

2.2

Installation in the Densité frame.......................................................................................................... 9

2.3

Installation of the Optical Interface (option) ........................................................................................ 9

2.4

Installation of the Audio Modules (option)........................................................................................... 9

2.5

ABUS Connection to Companion Audio Cards................................................................................... 9

2.6

Rear Panels and Connectors............................................................................................................ 10

User Interface ........................................................................................................................... 14

3.1

Control options .................................................................................................................................. 14

3.2

Card-Edge Status LED ..................................................................................................................... 14

Local control using the Densité frame control panel ........................................................... 16

4.1

Overview ........................................................................................................................................... 16

4.2

Menu for local control........................................................................................................................ 16

Remote control using iControl ............................................................................................... 17

5.1

The iControl graphic interface window.............................................................................................. 17

5.2

Video Input/Output panel .................................................................................................................. 20

5.2.1

Input/Output Config Tab....................................................................................................... 21

5.2.2

Input 2 tab ............................................................................................................................ 21

5.2.3

Deglitcher tab ....................................................................................................................... 22

5.2.4

Freeze tab ............................................................................................................................ 24

5.3

Video Processing panel .................................................................................................................... 25

5.3.1

Basic tab .............................................................................................................................. 25

5.3.2

Advanced tab ....................................................................................................................... 26

5.4

Video Outputs panel – 3G/HD Output tab ........................................................................................ 26

5.4.1

ARC tab................................................................................................................................ 28

5.4.2

Timing tab ............................................................................................................................ 31

5.4.3

Advanced tab ....................................................................................................................... 31

5.4.4

Meta tab ............................................................................................................................... 32

5.4.5

AFD tab ................................................................................................................................ 34

5.4.6

De-interlacer tab .................................................................................................................. 35

5.5

Video Outputs panel – SD Output tab .............................................................................................. 36

5.5.1

ARC

tab................................................................................................................................ 37

5.5.2

Timing tab ............................................................................................................................ 41

Summary of Contents for XVP-3901 DENSITE series
















































































































































Search results

Summary of Contents for XVP-3901 DENSITE series

Reviews:

Related manuals for XVP-3901 DENSITE series

Brands by name

Popular brands

Miranda XVP-3901 DENSITE series, Manual To Installation And Operation

Search results

Summary of Contents for XVP-3901 DENSITE series

Reviews:

Related manuals for XVP-3901 DENSITE series

Brands by name

Popular brands