Minolta EP3050 Operator'S Manual Download Page 156

Page: 156 / 206

Misfeed Clearing Procedures

Copier EP4050/3050

Swing down the Front Door and
remove the Exit Tray.

Be careful not to touch the areas
marked with

High

Voltage

and

Caution

with bare hands.

NOTE

Open the Left Door. Pushing and, at
the same time, turning Misfeed
Removal Knob M1 , pull out the sheet
of paper.

Swing Transport Section Release
Lever M2 down.

Close the Left Door and fit the Exit
Tray back into position.

Turning Misfeed Removal Knob M3 ,
pull out the sheet of paper.

Swing Transport Section Release
Lever M2 back to its original
position. Close the Front Door.

1136O035AA

1136O037AA

1136O038AA

1136O039AA

1136O036AA

r 5

a M

sag

e A

ppea

4. When the Message "Misfeed detected." Appears

144

Summary of Contents for EP3050















































































































































































































Search results

Summary of Contents for EP3050

Reviews:

Related manuals for EP3050

Brands by name

Popular brands

Minolta EP3050, Operator'S Manual

Search results

Summary of Contents for EP3050

Reviews:

Related manuals for EP3050

Brands by name

Popular brands