Minolta EP3050 Operator'S Manual Download

Page: 150 / 206

3. When the Message "The Staple Cartridge is empty." Appears

Auxiliary

Orig. Copy

The staple Cartridge is empty.
Please replace.

Auto Expo.

Auto Paper

x1.000

NonSort

Sort

Sort &
Staple

Group

Hole-

Punch

Basics

Finishing

1134P351CA

The message shown on the left appears when the
staples are running out.

Replace the Staple Cartridge with a new one by
following the procedure given below.

Replacing the Staple Cartridge for
ST-101

Holding the Lock Release Lever, slide
the Staple Sorter away from the copier.

1139O0490A

Open the Staple Cover.

While lifting the Staple Cartridge
Release Lever, pull the Staple
Cartridge out of its port.

1136O003AA

Pull the staple sheet about 3 cm out of
the new Staple Cartridge and break off
that portion.

1139O0970A

Check that no portion of the staple
sheet hangs out of the Cartridge. Break
off any portion of the sheet that hangs
out of the Cartridge.

NOTE

1134O077AA

r 5

a M

sag

e A

ppea

138

Summary of Contents for EP3050















































































































































































































Search results

Summary of Contents for EP3050

Reviews:

Related manuals for EP3050

Brands by name

Popular brands

Minolta EP3050, Operator'S Manual

Search results

Summary of Contents for EP3050

Reviews:

Related manuals for EP3050

Brands by name

Popular brands