Milwaukee PCG 12, Manual

Page: 5 / 55

3
English
7. Thread nuts and plunger onto the plunger rod in order shown (Fig. C).
Tighten back nut securely using the wrench provided.
NOTE: Make sure the front nut and plunger rod do not extend past the
front face of the plunger. If either part extends past the plunger, the back
cap of the material tube may rupture.
8. To remove carriage frame, reverse procedure.
Installing 850 g Carriage Frame Assembly
21 - Plunger rod
22 - Nut
23 - Plunger
24 - Carriage frame
25 - Double collar spacer
26 - Backing washer
27- Barrel nut
28 - Back nut
29 - Front nut
30 - Front face of plunger
1. Lock trigger or remove battery pack.
2. Press in and hold rod release trigger.
3. Grasp plunger rod handle and pull plunger rod back until the rod tip is
just inside of tool.
4. Release rod release trigger.
5. Insert double collar spacer into front face of tool body. The side with
the larger collar fits inside the tool. Place carriage frame over washer.
Assemble backing washer and barrel nut to tool as shown (Fig. D).
Tighten Barrel nut with wrench provided.
6. Press rod release trigger and push plunger rod forward to access the
threads on rod.
7. Thread nuts and plunger onto the plunger rod in order shown (Fig. D).
Tighten back nut securely using the wrench provided.
NOTE: Make sure the front nut and plunger rod do not extend past the
front face of the plunger. If either part extends past the plunger, the back
cap of the material tube may rupture.
8. To remove carriage frame, reverse procedure.
Installing Caulk or Adhesive Tube
31 - Double collar
32 - Backing washer
33 - Plunger rod
34 - Plunger
35 - Barrel plunger
36 - Nut
37- Nozzle cap
38 - Nozzle
39 - Barrel
40 - Barell nut
41 - Back cap
42 - Spacer
43 - Plunger
44 - Front face of plunger
1. Lock trigger or remove battery pack.
2. Cut nozzle of tube at an angle and size per manufacturer's recommen-
dation to suit the job. A smaller nozzle diameter requires more force to
push the caulk and reduces battery life.
3. Break inner seal of tube using a long nail or piece of wire. If the inner
seal is not broken, the caulk material may be forced out the rear end of
the tube and damage the tool.
NOTE: Before using a partially filled tube, remove any hardened material
with a long nail or piece of wire.
4. Press in and hold rod release trigger.
5. Grasp plunger rod handle and pull plunger rod back to allow the caulk
tube to fit inside carriage frame.
6. Insert caulk tube into carriage frame.
7. Push plunger rod handle forward until the plunger is against the caulk
tube.
8. Release rod release trigger.
Installing Barrel Assembly
1. Lock trigger or remove battery pack.
2. Press in and hold rod release trigger.
3. Grasp plunger rod handle and pull plunger rod back until the rod tip is
just inside of tool.
4. Release rod release trigger.
5. Position spacer and back cap (fine threads) onto nose of the tool as
shown (Fig. E). The side of the spacer with the double collar fits inside
the back cap.
6. Place backing washer on top of back cap and thread barrel nut into nose
of the tool as shown (Fig. E). Tighten nut using the spanner end of the
wrench provided with the tool.
7. Press rod release trigger and push plunger rod forward to access the
threads on rod.
8. Thread plunger, barrel plunger and nut onto the plunger rod in order
shown (Fig. E).
9. Thread barrel tube into back cap.
10. To remove barrel tube, reverse procedure.
Installing Sausage Type Pack
Always check sausage packs for punctures or damage to the pack
before installing. Do not use a damaged or frozen pack.
1. Lock trigger or remove battery pack.
2. Press in and hold rod release trigger.
3. Grasp plunger rod handle and pull plunger rod back to allow sausage
pack to fit inside barrel tube.
4. Insert pack into barrel tube.
5. Cut off end of sausage pack.
NOTE: Before using a partially filled pack, remove any hardened
material.
6. Insert nozzle supplied with the sausage pack into the nozzle cap
(coarse thread). Thread nozzle cap onto the front of barrel tube.
7. Cut nozzle at an angle and size per manufacturer's recommendation
to suit the job. A smaller nozzle diameter requires more force to push
the caulk and reduces battery life.
8. Press in and hold rod release trigger.
9. Push plunger rod handle forward until plunger is against sausage pack.
10. Release rod release trigger.
Operation
WARNING!
To reduce the risk of injury, ALWAYS wear safety goggles or
glasses with side shields.
Starting and Stopping and Controlling Speed
1. Pull trigger to dispense caulk.
2. Increase or decrease pressure on trigger to adjust the speed for proper
bead width and material feed rate. Material type, temperature and
nozzle diameter will all affect flow rate. When using a tube or pack with
a smaller nozzle diameter use a slower speed or the material may be
forced around the rear tube seat.
3. Release trigger to stop dispensing caulk.
D
E
E