Migatronic RCI2, User Manual

Page: 35 / 80

34 35
Analog Configuration file – PI PLASMA Standard
PI Plasma-DC with/without CWF - 10010602
Analog Configuration - 10010602 v1.02
PI Plasma-DC with/wihout CWF
10010602 Page 1 of 2
DIGITAL INPUTS (JMP1=Active-HIGH)
Pin# /
Military
Plug
Symbol Name Description Active
1 / m DIN15 !Quick-Stop Emergency stop
When input is H the machine can operate.
When input is L the welding will stop instantly without slope
down and the machine cannot start welding; the CWF also
stops feeding without retract.
L
2 / n DIN14 !Panel-Lock Panel locking
When input is H machine and CWF panels can be operated.
When input is L panels are locked (panels can be unlocked
also using “User-Menu”).
L
3 / Z DIN13 Pulse-Mode-Bit1 Current Pulse Mode Selection
Select current pulse mode based on inputs combination:
(Bit1)LL(Bit0)

No pulsation
(Bit1)LH(Bit0)  Slow-Pulse
(Bit1)HL(Bit0)

Fast-Pulse
(Bit1)HH(Bit0)  Synergic-Pulse
xx
4 / N DIN12 Pulse-Mode-Bit0
5 / P DIN11 Process-Selection Welding Process Selection
When input is L selects TIG-DC process.
When input is H selects PLASMA-DC process.
H
6 / T DIN10 Pilot-Trigger Start Plasma Pilot Arc
When input is H and Plasma process is selected the pilot-arc
is turned ON. When input is L the pilot-arc is turned OFF.
Pilot-arc can be operated also during welding.
H
7 / C DIN9 Program-Bit3 Welding Program Selection
Select program number based on inputs combination:
(Bit3)LLLL(Bit0)

Selected from machine
(Bit3)LLLH(Bit0)  Select program #1
(Bit3)LLHL(Bit0)

Select program #2
(Bit3)LLHH(Bit0)

Select program #3
…
(Bit3)HHHH(Bit0)

Select program #15
xxxx
8 / D DIN8 Program-Bit2
9 / G DIN7 Program-Bit1
10 / H DIN6 Program-Bit0
11 / X DIN5 Pulse-Wire Enable CWF Wire Pulse*
When input is H the pulsation of wire is enabled according to
the CWF settings. If Slow-Pulse with correct timings (see user
manual) is enabled the wire-pulse is synchronized with
current.
H
12 / W DIN4 Error-Reset Active Errors Reset
When input makes a L-to-H transition all errors on PI, CWF
and interface are cleared. If errors are not clearable error
signals remain active.
H
13 / U DIN3 Fwd-Wire-Inch Forward Wire Inching*
When arc is off wire can be jogged forward from the CWF by
setting this input H.
H
14 / V DIN2 Rev-Wire-Inch Reverse Wire Inching*
When arc is off wire can be jogged backward in the CWF by
setting this input H.
H
15 / S DIN1 Gas-Purge Gas Purge Control
Set this input H to start Shield and Plasma Gas purge. This
input has no effects during welding.
H
16 / R DIN0 Arc-Trigger Start Welding Arc
When input is H welding is started (other tasks as wire-inch,
gas purge etc. are aborted).
If Quick-Stop is active arc is not started.
When input going H-to-L, the actual wire-speed is latched
disregarding the analogue value at the analog input.
H