manualshive.com logo in svg

Migatronic RCI2, User Manual

Share
Download
Migatronic RCI2 User Manual Download Page 66

66

67

Software upgrade 

The software of microprocessor that controls the 
whole interface can be upgraded via SD CARD.
Latest software can be downloaded under Product 
software at  
www.migatronic.com/MY MIGATRONIC  
Save the software on an SD card containing the 
folders and one or more of the files shown below.
To order empty SD card, use item no. 12646000.
Valid software for this Robot Interface is stored 
into the folder ROBOT.

Software reading

•  Insert the SD card in the SD card reader.
•  Turn on the welding machine.
•  Wait until the display writes REMOVE SD CARD.
•  Turn off the machine and remove the SD card
•  The machine is now ready for use.
•  Insert the Configuration SD cards again.

Note:

 This operation does not affect the global configuration of interface (no configuration 

parameters are lost).

MIGA_SW

ROBOT

10020117.cry

(control software package)

Installing  

the Anybus module

1.  Important! Once you have installed 

the Anybus module, insert the plug 
straight into the hole.

2.  Press the plug slightly into position.
3.  Tighten the Anybus module using 

the screws. 

NOTE:
DEFECTIVE CONNECTORS ARE NOT 
COVERED BY WARRANTY!!!

Setup of Fieldbus communication.  
See page 11.

1

2

3

Summary of Contents for RCI2

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands