Miele KWT 6322 UG Operating And Installation Instructions Download | Manualshive

Page: 9 / 80

background image

IMPORTANT SAFETY INSTRUCTIONS

9



To ensure safe operation, use the wine conditioning unit only

when it has been installed.



The wine conditioning unit must be disconnected from the power

supply during installation, side-by-side heater installation, mainte-
nance and repair work. The appliance is only disconnected from the
power supply if:

– the circuit breaker has been tripped, or

– the power cord has been unplugged. Pull on the plug and not on

the cord when removing it from the outlet.



Installation, repair, and maintenance work should only be per-

formed by a Miele-authorized service technician.
Work by unqualified persons could be dangerous and may void the
warranty.



Repairs and other work performed by unauthorized persons could

be dangerous and may void the warranty.



Defective components should only be replaced by Miele original

parts. Only with these parts can the manufacturer guarantee the
safety of the appliance.

Proper use



The wine conditioning unit is designed for use within a certain cli-

mate range (ambient temperatures) and should not be used outside
this range. The climate range for your wine conditioning unit is stated
on the data plate inside the appliance. Installing it in a room with too
low an ambient temperature will cause the compressor to shut down
for longer periods of time so that the unit cannot maintain the re-
quired temperature.



Do not cover or block the air vents. This can impair the efficiency

of the appliance, increase the power consumption and cause dam-
age to the appliance.

«
...
7
8
9
10
11
...
»

Summary of Contents for KWT 6322 UG

















































































Reviews:

No comments

Related manuals for KWT 6322 UG

Spacemaker WSM2420S

Brand: GE Pages: 28

Spacemaker WSM2700

Brand: GE Pages: 8

Brand: Lang Pages: 21

Brand: Dash Pages: 25

Brand: ohmex Pages: 76

Brand: Anvil Pages: 16

Brand: Kambrook Pages: 20

Brand: Roller Grill Pages: 32

Brand: Magic Vac Pages: 68

Brand: Maestro Pages: 84

Brand: Cuisinart Pages: 16

Brand: Redmond Pages: 26

Brand: Cuisinart Pages: 20

Brand: Sub-Zero Pages: 39

Brand: Omcan Pages: 12

Brand: Toastmaster Pages: 9

Brand: Green Star Pages: 31

Brand: MOB Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands