Miele KWT 6322 UG Operating And Installation Instructions Download

Page: 26 / 80

Selecting additional settings

Acoustic signals



The wine conditioning unit has audible
tones such as the sensor tone and the
door and temperature alarms.

You can turn the sensor tone or the
acoustic door alarm on or off, but you
cannot turn off the temperature alarm.

There are four settings to choose from.
Option

is set at the factory, this

means that the sensor tone and the
door alarm are turned on.

Switching acoustic signals on/off



Touch the settings sensor.

All symbols available for selection will
appear on the display and the



sym-

bol will flash.



Touch the sensors for setting the
temperature (





) repeatedly until

the



symbol flashes on the display.



Touch the OK sensor to confirm the
selection.

The most recently selected setting
flashes and the



symbol lights up on

the display.



Now touch the





sensors to se-

lect:

: keypad tone off; door alarm off

: keypad tone off; door alarm on

(after 4 minutes)

: keypad tone off; door alarm on

(after 2 minutes)

: keypad tone on; door alarm on

(after 2 minutes)



Touch the OK sensor to confirm the
selection.

The selected setting is applied; the



symbol flashes.



Touch the settings sensor to exit set-
tings mode.
If you do not do this, the appliance
electronics will exit settings mode au-
tomatically after approximately
1 minute.

Summary of Contents for KWT 6322 UG

















































































Search results

Summary of Contents for KWT 6322 UG

Reviews:

Related manuals for KWT 6322 UG

Brands by name

Popular brands

Miele KWT 6322 UG, Operating And Installation Instructions

Search results

Summary of Contents for KWT 6322 UG

Reviews:

Related manuals for KWT 6322 UG

Brands by name

Popular brands