Miele KWT 6322 UG Operating And Installation Instructions Download

Page: 24 / 80

Selecting additional settings

Temperature unit (Celsius or
Fahrenheit)

The temperature can be displayed in ei-
ther Fahrenheit °F or Celsius °C. De-
grees Fahrenheit °F is the factory set-
ting.

Setting the temperature display to
Celsius



Touch the settings sensor.

All symbols available for selection will
appear on the display and the



sym-

bol will flash.



Touch the sensors for setting the
temperature (





) repeatedly until

°C and °F flash on the display.



Touch the OK sensor to confirm the
selection.

°F will flash on the display.



You can now select °C by touching
the





sensors.



Touch the OK sensor to confirm the
selection.

The selected setting is saved.



Touch the settings sensor to exit set-
tings mode.
If you do not do this, the appliance
electronics will exit settings mode au-
tomatically after approximately
1 minute.

The temperature will now be displayed
in Celsius.

Summary of Contents for KWT 6322 UG

















































































Search results

Summary of Contents for KWT 6322 UG

Reviews:

Related manuals for KWT 6322 UG

Brands by name

Popular brands

Miele KWT 6322 UG, Operating And Installation Instructions

Search results

Summary of Contents for KWT 6322 UG

Reviews:

Related manuals for KWT 6322 UG

Brands by name

Popular brands