Miele KWT 6322 UG Operating And Installation Instructions Download

Page: 23 / 80

Selecting additional settings

Certain settings on the wine condition-
ing unit can only be selected in settings
mode.

The door alarm is automatically dis-
abled when the appliance is in set-
tings mode.

Safety lock



The safety lock can be activated to pre-
vent:

– the appliance being turned off by

mistake,

– the temperature being changed by

mistake,

– DynaCool being turned on by mis-

take,

– the feature lighting being turned on

by mistake.

Activating and deactivating the safety
lock



Touch the settings sensor.

All symbols available for selection will
appear in the display and the



symbol

flashes.



Touch the OK sensor to confirm your
selection.

The last selected setting flashes and
the



symbol lights up in the display.



By touching the





sensor, you

can now select whether the safety
lock is activated or deactivated:

: the safety lock is deactivated

: the safety lock is activated.



Touch the OK sensor to confirm your
selection.

The selected setting will be adopted
and the



symbol will flash.



Touch the settings sensor to leave the
settings mode.
Otherwise the appliance will exit the
settings mode automatically after ap-
proximately one minute.

The



symbol will appear in the display

when the safety lock is activated.

Summary of Contents for KWT 6322 UG

















































































Search results

Summary of Contents for KWT 6322 UG

Reviews:

Related manuals for KWT 6322 UG

Brands by name

Popular brands

Miele KWT 6322 UG, Operating And Installation Instructions

Search results

Summary of Contents for KWT 6322 UG

Reviews:

Related manuals for KWT 6322 UG

Brands by name

Popular brands