Miele KWT 6322 UG Operating And Installation Instructions Download

Page: 36 / 80

Temperature and door alarm

Door alarm

An alarm will sound if the appliance
door has been left open for longer than
approx. 2 minutes. The sensors for the
two wine conditioning zones will flash in
the control panel. The alarm symbol



lights up on the display.

As soon as the appliance door is
closed, the alarm will stop. The sensors
for the two wine conditioning zones and
the alarm symbol



will go out in the

control panel.

If the alarm does not sound in the
event of a door alarm, then the alarm
has been switched off in settings
mode (see “Acoustic signals



” un-

der “Selecting additional settings”).

Turning the door alarm off early

If the alarm disturbs you, it can be
turned off early.



Touch the sensor to turn off the door
alarm.

The alarm will stop.
The wine conditioning zone sensors will
continue to flash and the alarm sym-
bol



will remain lit up until you close

the door.

Summary of Contents for KWT 6322 UG

















































































Search results

Summary of Contents for KWT 6322 UG

Reviews:

Related manuals for KWT 6322 UG

Brands by name

Popular brands

Miele KWT 6322 UG, Operating And Installation Instructions

Search results

Summary of Contents for KWT 6322 UG

Reviews:

Related manuals for KWT 6322 UG

Brands by name

Popular brands