Miele G 7966 Operating Instructions Manual Download Page 98

Page: 98 / 124

Frequently Asked Questions

Door release

Problem

Possible cause and solution

The in-operation
indicator light is
flashing quickly.
The alarm tone is
sounding.
The following fault is
indicated via the
display:

Before remedying the fault:



Switch the dishwasher off.



Door opening fault.

Switch the appliance off and
back on again. Read the
Operating Instructions for
additional details.

The door does not open automatically.
There may be a technical fault.



Open the door manually (see “Opening the door”
under “Before using for the first time”) and turn the
dishwasher back on again.



If the same fault message appears again, contact
Miele Service.

The door does not close automatically.
The door might be obstructed by an item inside the
appliance.



If this is the case, remove the item causing an
obstruction and turn the dishwasher on again.



If the same fault message appears again, contact
Miele Service.

Summary of Contents for G 7966





























































































































Search results

Summary of Contents for G 7966

Reviews:

Related manuals for G 7966

Brands by name

Popular brands

Miele G 7966, Operating Instructions Manual

Search results

Summary of Contents for G 7966

Reviews:

Related manuals for G 7966

Brands by name

Popular brands