Miele G 7966 Operating Instructions Manual Download Page 36

Page: 36 / 124

Settings

Rinse aid

You can adjust the rinse aid dosage for
best results.
The rinse aid dosage can be set from 0
to 6 ml.
3 ml is the factory default setting.

The rinse aid dosage can turn out to be
higher than the set value due to the
automatic adjustment of the program.

If spots appear on dishware:

- Increase the rinse aid dosage.

If clouding or smearing appears on
dishware:

- Decrease the rinse aid dosage.

Miele@home

Your dishwasher is equipped with an
integrated WiFi module.

You can connect your dishwasher to
your WiFi network.
This will increase the energy
consumption, even when the
dishwasher is turned off.

The Settings and Miele@home settings
menus will be added as additional
menu options.

Make sure that your WiFi network
signal strength is strong enough at
the installation site of your
dishwasher.

There are a number of ways of
connecting your dishwasher to your
WiFi network:

Summary of Contents for G 7966





























































































































Search results

Summary of Contents for G 7966

Reviews:

Related manuals for G 7966

Brands by name

Popular brands

Miele G 7966, Operating Instructions Manual

Search results

Summary of Contents for G 7966

Reviews:

Related manuals for G 7966

Brands by name

Popular brands