manualshive.com logo in svg

MicroNet SP5736P, User Manual

Share
Download
MicroNet SP5736P User Manual Download Page 32

SP5736P User’s Manual

 

31 

Time Interval: 

This item is for users to adjust the value of the time interval between each 
detected motion. 
 

Motion Window:

 

This item is used to set detection areas, and each IP camera might provide 
different amount of detection areas. Follow steps below to select the detection 
area. 

  First, select a number next to <Motion Window>.   

  Click and drag the mouse to choose the area users wish to set as the 

detection area. The number that users previously chose will show in the 
middle of the selected area. 

  Lastly, click on <Apply> button to save the setting. 

 

Repeat the above steps to set other detection areas. 
 
 

3.7.3  

Event Setup 

Enter Event Setup menu to configure event settings for each selected IP 
camera. The menu is displayed as below. 
 

Event Setup 

Channel   Vloss   Motion  AlmIn    AlmOut
CH01 Off Off Off Off 
CH02 Off Off Off Off 
CH03 Off Off Off Off 
CH04 Off Off Off Off 
CH05 Off Off 

Off Off 

CH06 Off Off 

Off Off 

 

 
Video Loss 

This item allows users to enable or disable Video Loss as an alarm event. 
Select <On> to enable Video Loss alarm events, or <Off> to disable. 
 

Summary of Contents for SP5736P





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands