Metapace T-2 Command Manual Download Page 46

Page: 46 / 54

Rev. 1.00

- 46 -

Metapace T-2

GS B n
[Name]
[Format]

[Range]
[Default]
[Description]

Turns white/black reverse printing mode on / off.

ASCII GS B n

Hex 1D

Decimal 29 66 n

≤

255

n=0

▪

Turns white/black reverse printing mode on or off.

- When the LSB of n is 0, white/black reverse mode is turned off.
- When the LSB of n is 1, white/black reverse mode is turned on.

GS H n
[Name]
[Format]

[Range]
[Default]
[Description]

Selects the printing position of HRI characters.

ASCII GS H n

Hex 1D

Decimal 29 72 n

≤

3, 48

≤

n=0

▪

Selects the printing position of HRI characters when printing a bar code.

- n selects the execution of printing and the printing position as follows :

Printing position

0, 48  Not printed.
1, 49  Above the bar code.
2, 50  Below the bar code.
3, 51  Both above and below the bar code.

GS I n
[Name]
[Format]

[Range]

[Description]

Transmits printer ID.

ASCII GS I n

Hex 1D

Decimal 29 73 n

≤

3, 49

≤

51, 65

≤

69, n=112

≤

3, 49

≤

51, 65

≤

69, (when TM-T88II compatible mode is

selected.)

▪

Transmits the printer ID specified.

- n specifies the types of the printer ID.

Printer ID type

1, 49 Printer model ID

Hexadecimal : 20H Decimal : 32

2, 50 Type ID

See table below.

3, 51 Firmware version ID

Depends on firmware version.

- n specifies the printer information.

Printer ID type

Firmware version

Depends on firmware version

66 Manufacturer

METAPACE

67 Printer

name

T-2

Summary of Contents for T-2























































Search results

Summary of Contents for T-2

Reviews:

Related manuals for T-2

Brands by name

Popular brands

Metapace T-2, Command Manual

Search results

Summary of Contents for T-2

Reviews:

Related manuals for T-2

Brands by name

Popular brands