MerCruiser QSD 2.0 Manual Download Page 39

Page: 39 / 135

Section 3 - On the Water

90-8M0057081

eng

MARCH 2011

Page 31

Any unexpected, sudden reduction in boat speed could result in the elevated passenger falling over the front of the boat.

mc79557-1

Wave and Wake Jumping

WARNING

Wave or wake jumping can cause serious injury or death from occupants being thrown within or out of the boat. Avoid wave or

wake jumping whenever possible.

mc79680-1

Operating recreational boats over waves and wakes is a natural part of boating. However, when this activity is done with enough

speed to force the boat hull partially or completely out of the water, certain hazards arise, particularly when the boat re‑enters the

water.
The primary concern is the boat changing direction while in the midst of the jump. In such cases the landing may cause the boat

to violently veer in a new direction. Such a sharp change in direction or turn can cause occupants to be thrown out of their seats

or out of the boat.
There is another less common hazardous result from allowing your boat to launch off of a wave or wake. If the bow of your boat

pitches down far enough while airborne, upon water contact it may penetrate under the water surface and submarine for an instant.

This will bring the boat nearly to a stop in an instant and can send the occupants flying forward. The boat may also veer sharply

to one side.

Impact with Underwater Hazards

Reduce speed and proceed with caution whenever you're driving a boat in shallow water or in areas where the waters are

suspected of having underwater obstacles that could be struck by the underwater drive components, rudder, or the boat bottom.

mc79679-1

IMPORTANT: The most important thing you can do to help reduce injury or impact damage from striking a floating or underwater

object is control the boat speed. Under these conditions, boat speed should be kept to a maximum speed of 24 to 40 km/h

(15 to 25 MPH).
The following demonstrate some, but not all, examples of what can happen if the boat strikes an object:
•

The boat could move suddenly in a new direction. Such a sharp change in direction or turn can throw occupants out of their

seats or out of the boat.

•

A rapid reduction in speed. This will cause occupants to be thrown forward, even out of the boat.

•

Impact damage to the underwater drive components, rudder, or boat.

Summary of Contents for QSD 2.0








































































































































Search results

Summary of Contents for QSD 2.0

Reviews:

Related manuals for QSD 2.0

Brands by name

Popular brands

MerCruiser QSD 2.0, Manual

Search results

Summary of Contents for QSD 2.0

Reviews:

Related manuals for QSD 2.0

Brands by name

Popular brands