MerCruiser QSD 2.0 Manual Download Page 78

Page: 78 / 135

Section 5 - Maintenance

Page 70

90-8M0057081

eng

MARCH 2011

3. Remove the water‑separating fuel filter and sealing ring from the mounting bracket. Do not use a filter wrench.

Typical

a -

Water‑separating fuel filter

NOTE: It may be necessary to keep the existing drain cap and use it on the new filter. Be sure to replace the O‑ring on the

drain cap.

4. Remove the drain cap and O‑ring seal from the bottom of the existing fuel filter. Note the position of the O‑ring seal.

Typical

a -

Drain cap

b -

O‑ring seal

5. Discard the used filter and O‑ring seal as defined by local authorities.
6. Install the O‑ring and drain cap on the new water‑separating fuel filter.

Typical

a -

Drain cap

b -

O‑ring seal

23459

24566

24568

Summary of Contents for QSD 2.0








































































































































Search results

Summary of Contents for QSD 2.0

Reviews:

Related manuals for QSD 2.0

Brands by name

Popular brands

MerCruiser QSD 2.0, Manual

Search results

Summary of Contents for QSD 2.0

Reviews:

Related manuals for QSD 2.0

Brands by name

Popular brands