MerCruiser QSD 2.0 Manual Download Page 75

Page: 75 / 135

Section 5 - Maintenance

90-8M0057081

eng

MARCH 2011

Page 67

Air Filter

Removal

1. Loosen the clamp and remove the oil separator vent hose.
2. Loosen the clamp and remove the air filter housing from the turbocharger inlet.

Air filter housing installed on engine

a -

Air filter housing

b -

Oil separator vent hose

c -

Air intake retaining clamp

3. Remove the air filter element from the air filter housing

a -

Air filter housing

b -

Air filter element

Inspection

1. The air filter cannot be cleaned. Replace the air filter if it is dirty or contaminated.
2. Replace the air filter if the foam element is deteriorated or torn.
3. Replace the air filter at the recommended interval. See

Maintenance Schedules

for the replacement interval under normal

conditions.

Installation

IMPORTANT: The foam cover is an integral component of the air filter element and must be clean and dry for proper filtration and

engine performance. Do not treat the foam filter cover with oil.

25357

25893

Summary of Contents for QSD 2.0








































































































































Search results

Summary of Contents for QSD 2.0

Reviews:

Related manuals for QSD 2.0

Brands by name

Popular brands

MerCruiser QSD 2.0, Manual

Search results

Summary of Contents for QSD 2.0

Reviews:

Related manuals for QSD 2.0

Brands by name

Popular brands