manualshive.com logo in svg

MerCruiser QSD 2.0, Manual, Page: 17 / 135

Share
Download
MerCruiser QSD 2.0 Manual Download Page 17

Section 2 - Getting to Know Your Power Package

90-8M0057081   

eng

  MARCH  2011

Page  9

The owner or operator is not to modify the engine in any manner that would alter the horsepower or allow exhaust gas emission

levels to exceed their predetermined factory specifications.

QSD engine data plate

a -

Engine serial number

b -

Cummins MerCruiser Diesel model information

c -

Emissions certification information

d -

Fuel rate

e -

Rated operation engine speed

f -

Governed engine speed

g -

Minimum idle speed

h -

Engine power rating

i -

Engine weight

j -

Emissions data

k -

Manufacturer model number, IMO type, liters per cylinder

Emissions Information

Exhaust Gas Emissions Certificate

A tamper‑resistant exhaust gas emission label is affixed to the engine's integrated exhaust manifold and expansion tank assembly

at the time of manufacture by Cummins MerCruiser Diesel. Please note that the exhaust gas emissions certification will not affect

the fit, function, or performance of the engine. Neither boatbuilders nor dealers may remove the exhaust gas emission label or

the part it is affixed to before sale. If modifications require the removal or cause damage to the exhaust gas emission label, contact

Cummins MerCruiser Diesel about the availability of a replacement before proceeding.

IN THE UNITED STATES, THIS ENGINE IS CATEGORIZED          
AS A RECREATIONAL ENGINE UNDER 40 CFR PART 94.

4937335

INSTALLATION OF THIS ENGINE IN ANY NON-RECREATIONAL 
VESSEL IS A VIOLATION OF FEDERAL LAW  SUBJECT TO 
PENALTY

25387

Exhaust gas emission label

Owner Responsibility

Neither the owner nor operator is to modify the engine in any manner that would alter the horsepower or allow exhaust gas emission

levels to exceed their predetermined factory specifications.

25401

a

b

c

d

e

f

g

h

i

j

k

Summary of Contents for QSD 2.0








































































































































Reviews:

No comments