MerCruiser QSD 2.0 Manual Download Page 118

Page: 118 / 135

Section 5 - Maintenance

Page 110

90-8M0057081

eng

MARCH 2011

2. Replace the belt if worn or damaged it must be replaced. See your Cummins MerCruiser Authorized Repair Facility.

a -

Power–assisted steering stretch belt

b -

Power–assisted steering pump pulley

c -

Crankshaft pulley

3. There is no adjustment available for the power‑assisted steering pump stretch‑belt. If the belt becomes loose or noisy it has

worn out and must be replaced. See your Cummins MerCruiser Authorized Repair Facility.

Serpentine Belt Inspection

The 2.0 diesel engine is equipped with a stretch‑belt that is used to drive the power‑assisted steering pump. This belt must be

removed to service the serpentine belt. Stretch‑belt service and maintenance procedures differ significantly from those that apply

to standard accessory drive belts. Should the serpentine belt need replacement consult your Cummins MerCruiser Authorized

Repair Facility.
1. Inspect the belt for proper tension and for the following:

•

Excessive wear

•

Cracks

NOTE: Minor, transverse cracks (across the belt width) may be acceptable. Longitudinal cracks (in the direction of belt

length) that join transverse cracks are not acceptable.

•

Fraying

•

Glazed surfaces

21062

2. Check the operation of the automatic tensioner and associated components.

a. Position a suitable tool on the automatic tensioner pulley bolt.

25604

Summary of Contents for QSD 2.0








































































































































Search results

Summary of Contents for QSD 2.0

Reviews:

MerCruiser QSD 2.0, Manual, Page: 118 / 135

Search results

Summary of Contents for QSD 2.0

Reviews: