MerCruiser QSD 2.0 Manual Download Page 83

Page: 83 / 135

Section 5 - Maintenance

90-8M0057081

eng

MARCH 2011

Page 75

On models equipped with a seawater strainer

, remove the hoses at the seawater strainer and drain them completely. Drain

and empty the seawater strainer. Reconnect the hoses and tighten the hose clamps securely.

Typical

a -

Seawater inlet

b -

Seawater outlet

c -

Seawater strainer cover

9. After the seawater has completely drained, remove the temporary drain hose and close the heat exchanger seawater drain

valve.

10. Reconnect all seawater hoses.
11. Tighten all hose clamps to specification.

Description

lb–in.

lb–ft

Hose clamp

5.6

–

Sterndrive Water Inlets Check

1. Obtain a piece of wire that will fit into the water inlets holes.
2. Insert the wire in and out of the sterndrive water inlets to ensure that they are open and to remove debris or marine growth.

Do not scrape the sterndrive paint.

3. Remove the wire from the sterndrive and retain for periodic water inlet checks.

5773

Alpha and Bravo sterndrive side pickup water inlet location

25831

Summary of Contents for QSD 2.0








































































































































Search results

Summary of Contents for QSD 2.0

Reviews:

Related manuals for QSD 2.0

Brands by name

Popular brands

MerCruiser QSD 2.0, Manual

Search results

Summary of Contents for QSD 2.0

Reviews:

Related manuals for QSD 2.0

Brands by name

Popular brands