MerCruiser QSD 2.0 Manual Download Page 106

Page: 106 / 135

Section 5 - Maintenance

Page 98

90-8M0057081

eng

MARCH 2011

2. Lubricate the driveshaft grease fittings by applying approximately 3 ‑ 4 pumps of grease from a typical hand‑operated grease

gun.

a -

Driveshaft grease fittings

b -

Transom end grease fitting

c -

Engine end grease fitting

Tube Ref No.

Description

Where Used

Part No.

U-joint and Gimbal

Bearing Grease

Transom end grease fitting, engine end grease fitting,

driveshaft grease fittings

92-802870A1

Sterndrive, Bellows, and Engine Alignment

NOTE: Have your Cummins MerCruiser Diesel Authorized Repair Facility perform the maintenance procedures listed, or refer to

the appropriate

Mercury MerCruiser Alpha Sterndrive Service Manual

1. Lubricate the sterndrive U‑joint O‑rings and driveshaft splines.

Alpha Sterndrive

a -

U‑joint O‑rings (3)

b -

Driveshaft splines

Bravo Sterndrive

a -

U‑joint shaft splines

b -

U‑joint shaft O‑rings

17014

17293

19867

Summary of Contents for QSD 2.0








































































































































Search results

Summary of Contents for QSD 2.0

Reviews:

Related manuals for QSD 2.0

Brands by name

Popular brands

MerCruiser QSD 2.0, Manual

Search results

Summary of Contents for QSD 2.0

Reviews:

Related manuals for QSD 2.0

Brands by name

Popular brands