manualshive.com logo in svg

MerCruiser QSD 2.0, Manual, Page: 20 / 135

Share
Download
MerCruiser QSD 2.0 Manual Download Page 20

Section 2 - Getting to Know Your Power Package 

Page  12

90-8M0057081   

eng

  MARCH  2011

The serial number is also stamped on the gimbal housing. This is used as a permanent reference for Cummins MerCruiser Diesel

Authorized Repair Facilities.

Gimbal housing with serial

number stamping

a -

Transom assembly serial

number

Instrumentation—QSD Sterndrive Models

Digital Gauges

A Cummins MerCruiser Diesel SmartCraft instrument package may be provided with this product. A few of the functions the

instrument package will display are engine RPM, coolant temperature, oil pressure, battery voltage, fuel consumption, and engine

operating hours.

Typical SmartCraft gauges

a -

Tachometer

b -

Speedometer

c -

LCD system view display

The SmartCraft instrument package will also aid in identifying the fault codes associated with the sounding of the engine audio

warning system. The SmartCraft instrument package will display critical engine alarm data and relate other potential problem

areas on its LCD display.
Refer to the manual with your gauge package for the warning functions monitored and basic operation of the SmartCraft Instrument

package.

Instruments—Sterndrive models

The following briefly explains the instrumentation typically found on some boats. The owner and operator should be familiar with

all the instruments and their functions on the boat. Because of the large variety of instrumentation and manufacturers, have your

boat dealer explain the gauges and normal readings that will appear on your boat.

25905

a

24575

a

b

cc

Summary of Contents for QSD 2.0








































































































































Reviews:

No comments