MerCruiser QSD 2.0 Manual Download Page 67

Page: 67 / 135

Section 5 - Maintenance

90-8M0057081

eng

MARCH 2011

Page 59

Bravo Sterndrive Gear Lube

Sterndrive Gear Lube

NOTICE

Discharge of oil, coolant, or other engine/drive fluids into the environment is restricted by law. Use caution not to spill oil, coolant,

or other fluids into the environment when using or servicing your boat. Be aware of the local restrictions governing the disposal

or recycling of waste, and contain and dispose of fluids as required.

Checking

NOTE: The gear lube level will fluctuate during operation. The gear lube level should be checked with the engine cold, before

starting.

1. Check the gear lube monitor to determine the gear lube level. Keep the gear lube level within the recommended operating

range. See

Filling

Gear lube level shown is at the correct operating range

a -

"ADD" mark

b -

"OPERATING RANGE" mark

IMPORTANT: If any water is visible at the bottom of the gear lube monitor or appears at the fill and drain plug hole, or if the

gear lube appears discolored, contact your Cummins MerCruiser Diesel Authorized Repair Facility immediately. Both

conditions may indicate a water leak in the sterndrive.

Filling

IMPORTANT: If more than 59 ml (2 fl. oz.) of High Performance Gear Lube is required to fill the gear lube monitor, a seal may be

leaking. Damage to the sterndrive may occur due to lack of lubrication. Contact your Cummins MerCruiser Diesel Authorized

Repair Facility .
1. Remove the gear lube monitor cap.
2. Fill the gear lube monitor with the specified gear lube so that the gear lube level is in the operating range. Do not overfill.

Gear lube monitor

a -

Gear lube level at the "ADD" mark

b -

Gear lube level at the "OPERATING RANGE" mark

c -

Gear lube monitor cap

Tube Ref No.

Description

Where Used

Part No.

High Performance Gear

Lube

Gear lube monitor

92-858064K01

19948

19947

Summary of Contents for QSD 2.0








































































































































Search results

Summary of Contents for QSD 2.0

Reviews:

Related manuals for QSD 2.0

Brands by name

Popular brands

MerCruiser QSD 2.0, Manual

Search results

Summary of Contents for QSD 2.0

Reviews:

Related manuals for QSD 2.0

Brands by name

Popular brands