be adjusted with the
Brightness Display/
Brightness Display/
switches:
switches:
function.
X
Press the
=
or
;
button on the steering
wheel to select the
Settings
Settings
menu.
X
Press the
:
or
9
button to select the
Lights
Lights
submenu.
X
Press
a
to confirm.
X
Press the
:
or
9
button to select the
Brightness Display/switches:
Brightness Display/switches:
function.
The current setting appears.
X
Press
a
to confirm.
X
Press the
:
or
9
button to adjust the
brightness to any level from
Level 1
Level 1
to
Level 5
Level 5
(bright).
X
Press the
a
or
%
button to save the
setting.
If the light switch is set to the
Ã
,
T
or
L
position, the brightness is dependent
upon the brightness of the ambient light.
i
The light sensor in the instrument cluster
automatically controls the brightness of the
multifunction display.
In daylight, the displays in the instrument
cluster are not illuminated.
Switching the daytime driving lights
on/off
X
Press the
=
or
;
button on the steering
wheel to select the
Settings
Settings
menu.
X
Press the
:
or
9
button to select the
Lights
Lights
submenu.
X
Press
a
to confirm.
X
Press the
:
or
9
button to select the
Day lights
Day lights
function.
If the
Day
Day lights
lights
function has been switched
on, the cone of light and the
W
symbol in
the multifunction display are shown in
orange.
X
Press the
a
button to save the setting.
Further information on daytime driving lights
(
Y
page 114).
Switching the Intelligent Light System
on/off
X
Press the
=
or
;
button on the steering
wheel to select the
Settings
Settings
menu.
X
Press the
:
or
9
button to select the
Lights
Lights
submenu.
X
Press
a
to confirm.
X
Press the
:
or
9
button to select the
Intell. Light System
Intell. Light System
function.
If the
Intell. Light Sys.
Intell. Light Sys.
function has
been switched on, the cone of light and the
L
symbol in the multifunction display are
shown in orange.
X
Press the
a
button to save the setting.
When you switch the
Intell. Light Sys.
Intell. Light Sys.
function on, you activate the following func-
tions:
R
Motorway mode
R
Active light function
R
Cornering light function
R
Extended range foglamps
If you set the dipped-beam headlamps for driv-
ing on the right/left, the multifunction display
shows the
Intell. Light System: system
Intell. Light System: system
inoperative Inactive for left-side
inoperative Inactive for left-side
traffic
traffic
or
Intell.
Intell. Light
Light System:
System: system
system
inoperative Inactive for right-side
inoperative Inactive for right-side
traffic
traffic
display message instead of the
Intell.
Intell. Light
Light System
System
function in the
Lights
Lights
submenu (
Y
page 224). This display message
will only appear if the setting for driving on the
left/right is set opposite to your vehicle's coun-
try version.
Observe the additional information on the Intel-
ligent Light System (
Y
page 116).
Setting the dipped-beam headlamps for
driving on the left/right
This function is only available in vehicles with
the Intelligent Light System.
You can use this function to switch between
symmetrical and asymmetrical dipped beam
(
Y
page 114).
X
Press the
=
or
;
button on the steering
wheel to select the
Settings
Settings
menu.
X
Press the
:
or
9
button to select the
Lights
Lights
submenu.
X
Press
a
to confirm.
X
Press the
:
or
9
button to select the
Dipped beams Setting for:
Dipped beams Setting for:
function.
You will see the selected setting:
Right-
Right-
side traffic
side traffic
or
Left-side traffic
Left-side traffic
.
X
Press the
a
button to save the setting.
If you change the setting, conversion does not
take place until the next time the vehicle is
stationary.
If you set the dipped-beam headlamps for driv-
ing on the right/left, then motorway mode and
224
Menus and submenus
On-boar
d
compu
ter
and
disp
lays
