Meltem M-WRG-II E-F Operating And Installation Instructions Download Page 53

Page: 53 / 60

Operating and installation instructions

M-WRG-II P-T (-F, -FC), M-WRG-II E-T (-F, -FC) ventilation units

- 53 -

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L A T I O N & H E A T R E C O V E R Y

16.2

Removing the cover from the ventilation unit

► Using both thumbs, press the two

latches (item 1 in Fig. 24) on the

bottom of the ventilation unit. The unit

cover will come away.

► At the same time, push your index

fingers into the gap between the unit

cover and housing, and lift the unit

cover up and away from the housing.

16.3

Removing the electronics compartment cover plate

► Use the screwdriver to loosen the

Torx screw (item 1 in Fig. 25) on the

electronics compartment cover plate

(item 2 in Fig. 25).

► Remove the electronics compartment

cover plate to access the connection

board (item 3 in Fig. 25).

Fig. 33: Removing the cover from the ventilation unit

Fig. 34: Removing the electronics compartment cover

plate

Summary of Contents for M-WRG-II E-F





























































Search results

Summary of Contents for M-WRG-II E-F

Reviews:

Related manuals for M-WRG-II E-F

Brands by name

Popular brands

Meltem M-WRG-II E-F, Operating And Installation Instructions

Search results

Summary of Contents for M-WRG-II E-F

Reviews:

Related manuals for M-WRG-II E-F

Brands by name

Popular brands