Meltem M-WRG-II E-F Operating And Installation Instructions Download Page 11

Page: 11 / 60

Operating and installation instructions

M-WRG-II P-T (-F, -FC), M-WRG-II E-T (-F, -FC) ventilation units

- 11 -

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L A T I O N & H E A T R E C O V E R Y

1.7.6 Air filters

Designation

Filter class

Outdoor air filter

ISO ePM1 60% (F7)

Activated charcoal filter for outdoor air (optional)

ISO ePM2,5 55% (F7)

Extract air filter

ISO Coarse 60% (G4)

1.8

Storage

► Store the ventilation unit in its original packaging in a dry place where the temperature

ranges between 0 °C and +40 °C.

1.9

Environmentally-friendly disposal

The ventilation units must not be disposed of in the residual waste bin.

► Dispose of the ventilation unit in accordance with the waste disposal regulations that

apply on site.

1.10

Revision index

Edition

Manual

Date

2nd edition Operating and installation instructions for

M-WRG-II P-T (-F, -FC) and M-WRG-II E-T (-F, -FC)

ventilation units

Week 43/2019 EN

1.11

Explanation of the symbols used

► This symbol indicates an action to be taken.

— This symbol indicates a list.

1.12

Supplementary documents

Manual

Part no.

Installation manual for flush-mount installation kit with plastering trim

(solid construction) M-WRG-II M/MB

744001EN

Installation manual for flush-mount installation kit M-WRG-II M (frame

construction)

744002EN

Installation manual for flush-mount installation kit M-WRG-II M-U

744003EN

Installation manual for M-WRG-II ventilation units

744004EN

Installation manual for outer wall terminals M-WRG-II ES (-P, -PK)

744005EN

Installation manual for window reveal installation kit

744006EN

User guide for wireless remote control M-WRG-FBH

5302-25-01

User guide for mobile operating hours reader M-WRG-ALGH

5302-26-01

Installation instructions and user guide for 4-way wireless pushbutton

switch M-WRG-FT

5301-14-01

Table 2: Supplementary documents

Summary of Contents for M-WRG-II E-F





























































Search results

Summary of Contents for M-WRG-II E-F

Reviews:

Related manuals for M-WRG-II E-F

Brands by name

Popular brands

Meltem M-WRG-II E-F, Operating And Installation Instructions

Search results

Summary of Contents for M-WRG-II E-F

Reviews:

Related manuals for M-WRG-II E-F

Brands by name

Popular brands