Meltem M-WRG-II E-F Operating And Installation Instructions Download Page 25 | Manualshive

Page: 25 / 60

background image

Operating and installation instructions

M-WRG-II P-T (-F, -FC), M-WRG-II E-T (-F, -FC) ventilation units

- 25 -

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L A T I O N & H E A T R E C O V E R Y

7.1.2 LED indicators on the ventilation unit

7.1.2.1 Selected ventilation program indicator

When a ventilation program is activated on the membrane touch pad, the corresponding

LED lights up (see Fig. 12 on page 23) for 10 seconds and then goes out again.

7.1.2.2 Status indicators

An LED that lights up continuously or flashes indicates one of the following ventilation unit

states:

LED in Fig. 12

Status

LED 1 lights up continuously

Air filter change required

LED 2 lights up continuously

Unit fault (e.g. faulty sensor or motor)

LED 3 flashes for 10 s

The absolute atmospheric humidity of the supply air is

greater than the absolute atmospheric humidity of the

extract air

LED 4 flashes for 10 s

The VOC value of the supply air is greater than

1500 ppm for 10 minutes (factory setting, only for units

with the M-WRG-II O/VOC-AUL option)

LED 5 flashes for 10 s

Ventilation unit in frost protection mode

«
...
23
24
25
26
27
...
»

Summary of Contents for M-WRG-II E-F





























































Reviews:

No comments

Related manuals for M-WRG-II E-F

Brand: Zephir Pages: 25

Brand: jbc Pages: 8

Brand: Kichler Lighting Pages: 48

Brand: ebm-papst Pages: 11

ALPATEC PONENT 16CR ELEGANCE

Brand: Taurus Pages: 56

Brand: ebm-papst Pages: 11

Brand: Nero Pages: 7

HELSINKI OSLO WIFI

Brand: UFESA Pages: 54

Brand: UltimateAir Pages: 32

Brand: S&P Pages: 36

Brand: Super Vac Pages: 12

Brand: Venture Industries Pages: 25

Mega Flow 6603-7109

Brand: HIRED-HAND Pages: 2

Brand: Harbor Breeze Pages: 17

Brand: ZIEHL-ABEGG Pages: 4

BENITO FP8003B Series

Brand: Fanimation Pages: 44

Brand: Coastal Pages: 20

Brand: Beldray Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands