Meltem M-WRG-II E-F Operating And Installation Instructions Download Page 19

Page: 19 / 60

Operating and installation instructions

M-WRG-II P-T (-F, -FC), M-WRG-II E-T (-F, -FC) ventilation units

- 19 -

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L A T I O N & H E A T R E C O V E R Y

5.2

Description of the functions

5.2.1 How the M-WRG-II ventilation unit works

Fig. 9:

How the ventilation unit works

Fig. 10: Components for air exchange

Item in

Fig. 9

Designation

Item in

Fig. 10

Designation

M-WRG-II ventilation unit

Extract air filter

Supply air

Supply air fan

Extract air

Cross-counterflow plate heat

exchanger

Outdoor air

Exhaust air fan

Exhaust air

Outdoor air filter

Outer wall terminal

The ventilation unit operates continuously, transports outdoor air and extract air at the

same time and guides and filters the outdoor air and extract air separately. The self-reg-

ulating fans (which ensure a constant volumetric flow rate) are arranged on the supply

air and exhaust air sides. The supply air fan (item 2 in Fig. 10) transports outdoor air

(item 4 in Fig. 9) through the outdoor air filter (item 5 in Fig. 10) and cross-counterflow

plate heat exchanger (item 3 in Fig. 10) into the interior as supply air (item 2 in Fig. 9).

The exhaust air fan (item 4 in Fig. 10) extracts the extract air (item 3 in Fig. 9) from the

interior. In the extract air filter (item 1 in Fig. 10), the extract air is cleaned, guided through

Summary of Contents for M-WRG-II E-F





























































Search results

Summary of Contents for M-WRG-II E-F

Reviews:

Related manuals for M-WRG-II E-F

Brands by name

Popular brands

Meltem M-WRG-II E-F, Operating And Installation Instructions

Search results

Summary of Contents for M-WRG-II E-F

Reviews:

Related manuals for M-WRG-II E-F

Brands by name

Popular brands